so... im going to build my engine...
#1
Elite Member
Thread Starter
iTrader: (24)
Join Date: Jun 2007
Location: Woodland Hills, CA
Posts: 4,667
Total Cats: 18
so... im going to build my engine...
and i need to know what parts to use because i am clueless!
i have about $1500-1700 for parts. help me choose
car is 1.6L and i will be shooting for 270-280whp for now and over 300whp by mid next year
i will be using t28/t3 hybrid out of my friends rb25det (he swapped for gt35) so i would want that thing to spool quickly. next year ill be swapping for an hks turbo most probably.
i have about $1500-1700 for parts. help me choose
car is 1.6L and i will be shooting for 270-280whp for now and over 300whp by mid next year
i will be using t28/t3 hybrid out of my friends rb25det (he swapped for gt35) so i would want that thing to spool quickly. next year ill be swapping for an hks turbo most probably.
#2
Elite Member
iTrader: (5)
Join Date: Jul 2006
Location: Central California
Posts: 2,557
Total Cats: 5
well ... pistons and rods have been discussed to death, youre gonna need those
8AN2-10-271 Engine gasket set $191 from mazdamotorsports.com:
headgasket, cam + main oil seals, waterpump gasket, valve seals, intake + ex. gaskets, and everything else you need for that
Main + thrust bearings (clevite) ~ $50
hopefully pistons come with good rings, otherwise, i dunno
well theres the basics. You are probably looking at around $1500 right there.
dont forget machine work, and do you want ARP crap? I consider that bling, but whatever.
8AN2-10-271 Engine gasket set $191 from mazdamotorsports.com:
headgasket, cam + main oil seals, waterpump gasket, valve seals, intake + ex. gaskets, and everything else you need for that
Main + thrust bearings (clevite) ~ $50
hopefully pistons come with good rings, otherwise, i dunno
well theres the basics. You are probably looking at around $1500 right there.
dont forget machine work, and do you want ARP crap? I consider that bling, but whatever.
#3
You need a set of these...
http://m-tuned.com/miatarods.html
Currently on sale @ $379
As for ARP, I normally recommend Head Bolts, but use stock Mains.
http://m-tuned.com/miatarods.html
Currently on sale @ $379
As for ARP, I normally recommend Head Bolts, but use stock Mains.
#5
IMO, you don't need ARP studs for the head or mains.
The head gasket is like the fuse in the engine. If something bad happens (like detonation) that could cause severe engine damage (damaged pistons, bent rods, etc), it's designed to blow and protect the engine. Putting head studs allows you to torque the head down about 40% higher than factory specs so the engine is less likely to blow a HG (but most people spend money on them and don't WTF?). But to me, I'd rather a HG blow if I have detonation than it hold and I crack a ring landing. Guess which one's cheaper and easier to fix?
Granted from what I hear, pre 99's had those shitty composite head gaskets that just suck. I would recommend getting the multi layered steel (MLS) one like what's on the 99+ from the factory.
Add to that the HG's are NOT prone to failure. They hold up well to high boost setups just fine (assuming you have the MLS gasket). IMO, don't waste your money on studs unless this is a race car.
FWIW, I hit my 99' with a 100 shot at idle one day. Detonation CITY! From the math, the motor was making over 600 ft*lbs of torque. Blew the hell out of the HG. Had it not, it would have surely broken the ring landings.
The head gasket is like the fuse in the engine. If something bad happens (like detonation) that could cause severe engine damage (damaged pistons, bent rods, etc), it's designed to blow and protect the engine. Putting head studs allows you to torque the head down about 40% higher than factory specs so the engine is less likely to blow a HG (but most people spend money on them and don't WTF?). But to me, I'd rather a HG blow if I have detonation than it hold and I crack a ring landing. Guess which one's cheaper and easier to fix?
Granted from what I hear, pre 99's had those shitty composite head gaskets that just suck. I would recommend getting the multi layered steel (MLS) one like what's on the 99+ from the factory.
Add to that the HG's are NOT prone to failure. They hold up well to high boost setups just fine (assuming you have the MLS gasket). IMO, don't waste your money on studs unless this is a race car.
FWIW, I hit my 99' with a 100 shot at idle one day. Detonation CITY! From the math, the motor was making over 600 ft*lbs of torque. Blew the hell out of the HG. Had it not, it would have surely broken the ring landings.
#7
Elite Member
Thread Starter
iTrader: (24)
Join Date: Jun 2007
Location: Woodland Hills, CA
Posts: 4,667
Total Cats: 18
so far im thinking about these:
wiseco 9:1 +1mm overbor
m-tuned rods
clevite bearings
fm +1mm head gasket
fm valve spring kit
web 505 cams
right there im looking at around $1700... add another $300-400 for all the gaskets, o-rings, etc and im just a tad over my budget but i should be good although id like to stay under $1700 if possible. what can i substitute?
wiseco 9:1 +1mm overbor
m-tuned rods
clevite bearings
fm +1mm head gasket
fm valve spring kit
web 505 cams
right there im looking at around $1700... add another $300-400 for all the gaskets, o-rings, etc and im just a tad over my budget but i should be good although id like to stay under $1700 if possible. what can i substitute?
#13
Elite Member
iTrader: (5)
Join Date: Jul 2006
Location: Central California
Posts: 2,557
Total Cats: 5
+1 on no need for springs or cams.
$300 - $400 for orings and seals? check out mazdamotorsports.com if you dont have an account, fill out the application and send a few pictures. It only took them like 3 days to approve my application and its an awesome tool to have because you can get oem parts at autozone prices.
through them the engine gasket kit is $190 including the headgasket. Thats what i would do. 15psi does not need a special headgasket to keep it in ... look at all the stock motors running 15psi all day long.
Just trying to save you some money.
cheers
$300 - $400 for orings and seals? check out mazdamotorsports.com if you dont have an account, fill out the application and send a few pictures. It only took them like 3 days to approve my application and its an awesome tool to have because you can get oem parts at autozone prices.
through them the engine gasket kit is $190 including the headgasket. Thats what i would do. 15psi does not need a special headgasket to keep it in ... look at all the stock motors running 15psi all day long.
Just trying to save you some money.
cheers
so far im thinking about these:
wiseco 9:1 +1mm overbor
m-tuned rods
clevite bearings
fm +1mm head gasket
fm valve spring kit
web 505 cams
right there im looking at around $1700... add another $300-400 for all the gaskets, o-rings, etc and im just a tad over my budget but i should be good although id like to stay under $1700 if possible. what can i substitute?
wiseco 9:1 +1mm overbor
m-tuned rods
clevite bearings
fm +1mm head gasket
fm valve spring kit
web 505 cams
right there im looking at around $1700... add another $300-400 for all the gaskets, o-rings, etc and im just a tad over my budget but i should be good although id like to stay under $1700 if possible. what can i substitute?