Rebuilding a VVT actuator with pics
#1
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,439
Total Cats: 1,214
Rebuilding a VVT actuator with pics
I'm quoting this from Davezorz, and I think it's a great post. Anybody think it'd be a good one to sticky? At the very least people can now search "rebuilding a vvt actuator", and get this thread as a result.
Please forgive my vocabulary, I am not sure what the proper names for all the pieces are:
Gear removed from Car
cover and 4 10 MM bolts removed. notice the brown puck sitting in the groove, it normally sticks to the cover when you pull it apart.
Rubber puck/bushing thingy everyone is talking about. Ignore the spring in the picture
removing the center assembly from the gear. Note the black apex seals, some are coming out with the center assembly.
Center assembly removed with all apex seals in their relative positions
Close up of center assembly
Close up of gear with center assembly removed
Close up of rear (camshaft) side of center assembly
Close up of apex seal with spring
removing locking pin from gear
Close up of locking pin
Gear with locking pin removed
locking pin engagement in center assembly
VVT assembly in fully advanced position
VVT assembly in fully retarded position (this is the position it locks in)
Gear removed from Car
cover and 4 10 MM bolts removed. notice the brown puck sitting in the groove, it normally sticks to the cover when you pull it apart.
Rubber puck/bushing thingy everyone is talking about. Ignore the spring in the picture
removing the center assembly from the gear. Note the black apex seals, some are coming out with the center assembly.
Center assembly removed with all apex seals in their relative positions
Close up of center assembly
Close up of gear with center assembly removed
Close up of rear (camshaft) side of center assembly
Close up of apex seal with spring
removing locking pin from gear
Close up of locking pin
Gear with locking pin removed
locking pin engagement in center assembly
VVT assembly in fully advanced position
VVT assembly in fully retarded position (this is the position it locks in)
#5
Retired Mech Design Engr
iTrader: (3)
Join Date: Jan 2013
Location: Seneca, SC
Posts: 5,012
Total Cats: 859
Curly, feel free to delete this post after answering, as sticky...
What does the rebuild part of this consist of? New apex seals, just cleaning out junk after an engine crash, etc ???
In other words, why do it? What to look for, what to change, etc. Inquiring minds want to know.
What does the rebuild part of this consist of? New apex seals, just cleaning out junk after an engine crash, etc ???
In other words, why do it? What to look for, what to change, etc. Inquiring minds want to know.
#6
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,439
Total Cats: 1,214
People reassembling incorrectly, and yes, cleaning. That or you think the right way to remove it is removing the 4 m6 bolts, not the 3 tiny bolts on the cover to get to the 17mm main bolt.
That and morbid curiosity.
That and morbid curiosity.
#8
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,439
Total Cats: 1,214
Miata roadster sells a great kit, with oil hard line o-ring, filter, housing gasket, 4 o-rings for the oil manifold, and one for the large case o-ring, pictured first in the 2nd photo above. Along with the actuator o-ring. They're all high temp viton, a much better material than standard rubber. All for $35. Highly recommended.
But no, the so called "apex seals" cannot be bought new as far as I know, and also don't wear out afaik. And the MR kit doesn't require you to go this far, or even un-do the timing belt.
No engine rebuild kit, oem or after market, includes these o-rings/gaskets.
But no, the so called "apex seals" cannot be bought new as far as I know, and also don't wear out afaik. And the MR kit doesn't require you to go this far, or even un-do the timing belt.
No engine rebuild kit, oem or after market, includes these o-rings/gaskets.
#9
Senior Member
iTrader: (2)
Join Date: Sep 2009
Location: Edmonton, AB, Canada
Posts: 1,193
Total Cats: 29
When I say Apex seals you say Mazda............................................. ...................Miata !
I'll have to see how far I took apart my VVT actuator when I get to that stage. I hope I didn't pull it all apart. I'm a little scarred.
I'll have to see how far I took apart my VVT actuator when I get to that stage. I hope I didn't pull it all apart. I'm a little scarred.
#13
Miata roadster sells a great kit, with oil hard line o-ring, filter, housing gasket, 4 o-rings for the oil manifold, and one for the large case o-ring, pictured first in the 2nd photo above. Along with the actuator o-ring. They're all high temp viton, a much better material than standard rubber. All for $35. Highly recommended.
But no, the so called "apex seals" cannot be bought new as far as I know, and also don't wear out afaik. And the MR kit doesn't require you to go this far, or even un-do the timing belt.
But no, the so called "apex seals" cannot be bought new as far as I know, and also don't wear out afaik. And the MR kit doesn't require you to go this far, or even un-do the timing belt.
I actually just sent Dave back his VVT actuator with new seals/sliders/ and puck that we had made. We didn't try making the metal springs, just the seals.
I agree that none of those pieces are really wear items, but we decided to see if we could make any replacement bits for the ones that either get lost or damaged after reassembly. It's probably answering a question nobody really asks, but it's for science, right?
We'll see how they hold up whenever he gets it installed and running.
#14
I need some help and clarification here. If you look at this post in miata.net, specifically if you look at the attached pictures in this post, the OP seems to install the locking pin and corresponding spring backwards or a least it appears to be installed backwards in comparison to the pictures in this thread. Can you clarify what is the proper way install the locking pin and corresponding spring and thank you very much for this super awesome thread.
VVT Solenoid assembly. - MX-5 Miata Forum
VVT Solenoid assembly. - MX-5 Miata Forum
#18
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,439
Total Cats: 1,214
Adding this pic for any future DIY'ers.
Reassembles in the same orientation shown, with the spring sitting on the rod, followed by the cap, and finally the c-clip.
Not really a reason to do disassemble the solenoid, but we recently had a bearing eat itself, so any and all oil related items are being thoroughly cleaned or replaced.
Reassembles in the same orientation shown, with the spring sitting on the rod, followed by the cap, and finally the c-clip.
Not really a reason to do disassemble the solenoid, but we recently had a bearing eat itself, so any and all oil related items are being thoroughly cleaned or replaced.
#19
Senior Member
iTrader: (2)
Join Date: Sep 2009
Location: Edmonton, AB, Canada
Posts: 1,193
Total Cats: 29
Mine is loud so i unplugged it for the last few months i drove the car. Sounded like a cross between rod and cam noise, freaked me out a bit. Unplugged its quiet of course. I'mgoing to pull it sometime and figure out what it is