Pumping oil out the PCV
#1
Junior Member
Thread Starter
iTrader: (5)
Join Date: Aug 2008
Location: Northbrook IL
Posts: 105
Total Cats: 0
Pumping oil out the PCV
I was at 10psi when the vacuum/boost line that goes to the (begi)fmu came off and the engine went lean. the car runs but not on all cylinders and oil is being pumped out the pcv hole in the valve cover.
The rings are gone in one cylinder?
The rings are gone in one cylinder?
#3
Junior Member
Thread Starter
iTrader: (5)
Join Date: Aug 2008
Location: Northbrook IL
Posts: 105
Total Cats: 0
yeh thats what i thought...
Should i get another stock bottom end or reuse my old pauter rods from my other engine and get some new JE pistons because my old ones have a ton of detonation marks on top? going to make less then 250whp
Should i get another stock bottom end or reuse my old pauter rods from my other engine and get some new JE pistons because my old ones have a ton of detonation marks on top? going to make less then 250whp
#6
Junior Member
Thread Starter
iTrader: (5)
Join Date: Aug 2008
Location: Northbrook IL
Posts: 105
Total Cats: 0
Its a vacuum/boost line to the FMU that came off and my fuel pressure went from 70psi to 43psi and i didn't notice. I got a parallel MS but never got around to installing it, i will probably go with a stock block again.
Thanks
Thanks
#7
My understanding was a mere few seconds of detonation was the very end of the motor itself...
Any pics of those rambo pistons? I feel like I've been getting a little det myself, just can't hear it :(
I'm also getting alot of blowby from my pcv... No oil coming out, but lots of air flow coming out of there at idle. Probably wouldn't hurt to do a compression check, but I maintain about 20 inches of vac at idle(900-1k rpms)
#8
Junior Member
Thread Starter
iTrader: (5)
Join Date: Aug 2008
Location: Northbrook IL
Posts: 105
Total Cats: 0
Ton of detonation marks? How much detonation could you have sustained and still have a running motor?
My understanding was a mere few seconds of detonation was the very end of the motor itself...
Any pics of those rambo pistons? I feel like I've been getting a little det myself, just can't hear it :(
I'm also getting alot of blowby from my pcv... No oil coming out, but lots of air flow coming out of there at idle. Probably wouldn't hurt to do a compression check, but I maintain about 20 inches of vac at idle(900-1k rpms)
My understanding was a mere few seconds of detonation was the very end of the motor itself...
Any pics of those rambo pistons? I feel like I've been getting a little det myself, just can't hear it :(
I'm also getting alot of blowby from my pcv... No oil coming out, but lots of air flow coming out of there at idle. Probably wouldn't hurt to do a compression check, but I maintain about 20 inches of vac at idle(900-1k rpms)
I was at 24/25 in at idle before this happened.
#10
Originally Posted by Turbobarber
How much detonation could you have sustained and still have a running motor?
Originally Posted by http://en.wikipedia.org/wiki/Engine_knocking
Detonation induced pre-ignition
... Eventually this [Detonation] can lead to the far more catastrophic Pre-Ignition as described above.
While it is not uncommon for an automobile engine to continue on for thousands of miles with mild detonation, preignition can destroy an engine in just a few strokes of the piston.
#13
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,729
Total Cats: 4,126
no, just boring lack of knowledge.
pre-ignition is just when the spark plugs get too hot and cause an explosion event before the desired time.
detonation doesn't lead to it, it however, can lead to detonation.
pre-ignition is just when the spark plugs get too hot and cause an explosion event before the desired time.
detonation doesn't lead to it, it however, can lead to detonation.
#14
This seems to be a well mis-understood area, so I'll post what I understand to be true.
This statement is true, although it doesn't have to be the spark plug that lights off the mixture too early.
Overheated exhaust valves or sharp edges in the combustion chamber (unradiused valve reliefs, etc) can cause pre-ignition once they become hot spots.
You're right, pre-ignition can lead to a detonation like event. However, there is an important difference.
In a standard detonation event, the two (or more) colliding pressure wave fronts are created by the spark plug firing, and the pressure rise due to the expanding wave front autoigniting the remainder of the mixture, respectively. However, this mode of detonation will always occur after the spark plug fires.
In a pre-ignition event, the flame front can be lit off by a hot spot before the spark plug has fired. This can lead to the cylinder achieving max pressure before the piston has reached TDC. Another piston will be on its power stroke, and (along with the engine's rotational inertia) will force the piston from the pre-ignition cylinder up against the high pressure, usually resulting in catastrophic damage. There will probably be a colliding wave front (detonation) in this situation due to the massive pressure rise, but if the pre-ignition occurs too soon before the spark is planned, it's all over anyway.
Detonation can lead to pre-ignition, in that repeated occurrences will break down the boundary layer of gas around the spark plug, and other edges, and can then allow these spots to heat up to a pre-ignition temperature.
This is the way I understand it. Feel free to disagree, but please post your reasoning if you'd like to discuss this more. I'm always eager to learn.
Originally Posted by Braineack
pre-ignition is just when the spark plugs get too hot and cause an explosion event before the desired time.
Overheated exhaust valves or sharp edges in the combustion chamber (unradiused valve reliefs, etc) can cause pre-ignition once they become hot spots.
Originally Posted by Braineack
detonation doesn't lead to it, it however, can lead to detonation.
In a standard detonation event, the two (or more) colliding pressure wave fronts are created by the spark plug firing, and the pressure rise due to the expanding wave front autoigniting the remainder of the mixture, respectively. However, this mode of detonation will always occur after the spark plug fires.
In a pre-ignition event, the flame front can be lit off by a hot spot before the spark plug has fired. This can lead to the cylinder achieving max pressure before the piston has reached TDC. Another piston will be on its power stroke, and (along with the engine's rotational inertia) will force the piston from the pre-ignition cylinder up against the high pressure, usually resulting in catastrophic damage. There will probably be a colliding wave front (detonation) in this situation due to the massive pressure rise, but if the pre-ignition occurs too soon before the spark is planned, it's all over anyway.
Detonation can lead to pre-ignition, in that repeated occurrences will break down the boundary layer of gas around the spark plug, and other edges, and can then allow these spots to heat up to a pre-ignition temperature.
This is the way I understand it. Feel free to disagree, but please post your reasoning if you'd like to discuss this more. I'm always eager to learn.