When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Unless the rings are bad, running both sides to a VTA catch can should work with:
Drilled out PVC or other open elbow on intake side.
No other special things done. (Un-Modified valve cover)
Plug the PVC port on the intake manifold.
That has been working fine for me at similar situation. There is some occasion odor at idle after a hard run as nothing is going into the intake to burn the fumes.
I have a simple catch can on a 1.8VVT with TD04 and only 250hp and 7,000rpm limit. Very little ever in the 0.4L catch can until yesterday when it was full of what looked like nothing but oil after a full track day. Changes since the previous day include:
Car was used very hard all day by three drivers with little rest between session The track has a looooong tightening right hander Track is clockwise There's a 120mph straight The car now has better brakes and stickier tyres
Will any of the above contribute to the 0.4L or is there now too much engine wear?
How is it plumbed? My exhaust side catch can (12an outlet and enlarged internal passage) only smells of fumes after a track day but the intake side can (normal PCV layout and hose with a can in the middle) fills like no tomorrow in one session and gets small quantity of pure oil on the street, I even tried copper scrubbers etc to baffle more. I just cap the intake side for track days as Savington has previously suggested.
Correction. It’s a 0.2L can. 0.2L after a hard track day seems not to be alarming. Very simple setup. Pics here. Big improvement on the previous owner’s simple filter which dropped oil on the exhaust manifold.
Correction. It’s a 0.2L can. 0.2L after a hard track day seems not to be alarming. Very simple setup. Pics here. Big improvement on the previous owner’s simple filter which dropped oil on the exhaust manifold.
There are several frightening things in those pictures. The least of which is that you don't appear to have read the thread you are posting in. I wish you well.
Just wanted to drop in with an additional data point to the discussion. Nothing new, just sharing what seems to have worked for me.
I initially must've misunderstood what I read here once upon a time and capped the cold side port, opened the hot side port and installed and AN-8 fitting and hose. I drove to the capital to get an alignment, a 100km round trip and my small catch can was overflowing. I was missing maybe 500ml of oil. it was not pretty, oil was actually just sputtering out of the port if I removed the hose.
So today I opened up the intake side again, installed an AN-8 bung and running both to a vented catch can. Resealed the plates on the underside, opened up the channel between chambers. Only got it up to temp and did a couple of pulls since it's late but there is absolutely nothing in the can. Not the greatest amount of data but it's looking way better than the sputtering mess I had yesterday.
I'm running a single sealed Moroso catch can connected between the intake manifold and PCV. I'm running a Ford 1.8 cover and have a breather tube connected to my turbo inlet pipe. I rarely get excessive oil buildup inside the can, usually just a small amount even after aggressive driving over long periods of time. I also don't have irregular build up in the inlet pipe.
Valve cover is unmodified. I know the setup doesn't look great now, but I wanted to install a better pipe/hose between the VC and inlet. What size AN fittings should be used with the valve cover and if I wanted shorter routing between the VC and inlet, where is a good spot to tap into on the cover? Is the normal outlet location on a Miata within the same baffle area on the Ford cover? Or because the Ford cover has the port on the rear of it does it travel through more baffling before it goes out of the cover?
There are several frightening things in those pictures. The least of which is that you don't appear to have read the thread you are posting in. I wish you well.
There are several frightening things in those pictures. The least of which is that you don't appear to have read the thread you are posting in. I wish you well.
No doubt there are several things that frighten you. But surely it's appropriate for you to respond when I ask you what they are?
Sixshooter commented that he saw several frightening things in these pics but won't tell me what they are.. Is anyone else able to tell me what's frightening so I can fix them?
Originally Posted by BARMY
Correction. It’s a 0.2L can. 0.2L after a hard track day seems not to be alarming. Very simple setup. Pics here. Big improvement on the previous owner’s simple filter which dropped oil on the exhaust manifold.
When under vacum you now have a vacum leak because the pcv is pulling crank case pressure but the crank case is vented to atmosphere by the hot side catch can that's vented to atmosphere. Under boost the pcv valave is closed so crank case pressure is forced thru the catch can witch is fine but the line is small and may not be able to evacuate enough pressure depending on how bad the blow by is.
You could remove the filter on the catch can and run a line to the turbo inlet pipe and leave pcv as is.
The other option would be vta only and you could cap the cold side completely but again the hot side hose needs to be bigger. Or you can get a vta can with 2 inlets and run the colt side to the can as well and just cap the pcv inlet at the intake manifold however a lot of people have issues with oil filling the can when running the cold side to a can.
All of this assumes you also enlarge the ports on the internal baffles on the valve cover.
Someone please advise if I'm wrong, this is my understanding but don't want to give bad info.
Nothing 'frightening' to me, but turbo blankets don't get a good wrap around here. I'd run a bigger catchcan, and if I ran a small one max the available volume by putting that VTA filter vertical. I'd do all the modz to the VC venting and run large diameter hose to said bigger catchcan located closer to the VC outlet (you may have done some of these already). Looks like you have a low point in that long hose, where moisture can condense - harder to shift fluid than vapour. 'P' clamps are your friend, lose the cable ties where you can. Short hose better than long hose. Not a big deal, but I'd shorten and/or realign the long bolt on the TB clamp so it doesn't rub the hose. That coolant overflow routing (i did the same) isn't being obstructed at the radiator bracket - your hose looks thicker than mine?
Overall, it looks like the engine bay was put together by a first-timer, or someone on a very tight budget, or someone who just wasn't thinking ahead. You run with a pretty experienced and capable crowd down there, any feedback from them?
Driven 200km on this setup now and not a drop in the can if I open the dump valve. Which is way better than overflowing after 100km lol. I might definitely route the vent under the car or into the exhaust. But so far it's working well.
Driven 200km on this setup now and not a drop in the can if I open the dump valve. Which is way better than overflowing after 100km lol. I might definitely route the vent under the car or into the exhaust. But so far it's working well.
Mine is set up just like yours (but more ghetto). Stock Valve Cover. I don't get any oil in the can on street. About 1 tablespoon (15ml) after a track day. See my post #121 above with a link to a picture of my set-up.
Yep. saw yours before making mine, definitely got some inspiration there. AN lines are wayyyy overkill for what it is but I'm planning on going extra wherever I can from now on. This winter I'll be redoing the engine bay completely