I don't trust my oil temp gauge
#21
Good idea Rick. I'm planning an oil change soon and will remove the sensor and dip in boiling water. Here is the best pic I could get of the sensor location. It is the black wire connected to the brass fitting on the block next to where the OEM oil filter was located before it was rerouted to the firewall. Looks like the original owner inserted a "y" fitting between the block and the OEM oil pressure sensor and inserted the AIM temp sensor in the other end of the "Y". The orientation of the pic is not accurate. Best I could do with my big hands and an iPhone. Seems like a good place to get accurate temp readings? What do you think?
#22
That is useless, there is no oil flow in that area. No wonder it reads so low and off. It needs to be installed in the pan ideally, or second best, in a fitting that has oil being pumped across it constantly so as the temp of the oil changes, the sensor can pick that up immediately. And of course, before the oil cooler. Goal is to measure how HOT the oil got. Best place to mount the sensor would be on the rod or main bearings. But that's extremely difficult to do, so oil pan is second best and 1000x more practical.
Philip
#24
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,455
Total Cats: 6,874
Stick that sensor into a sandwich plate located between the engine block and the stock heat exchanger (if still present), and in a location which places it *before* any type of oil cooler.
If uncertain, oil goes into the filter through the small holes around the outside, and comes out of the filter through the large hole in the middle. Situate sensor accordingly.
#25
Update: Installed a brand new sensor in the oil pan. Also installed coolant reroute kit and boxed in the radiator. Water temps are a little lower. Oil temp is about 15-20 degrees higher than before. Now oil hot at about 215. Oil temps would probably be a little higher if not for improved water cooling. Still seems a tad low but I'm not complaining. Thanks for all the advice.
#27
SADFab Destructive Testing Engineer
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Late to the party, but would that sensor location really stay cooler than the others. Its still in direct contact with oil, and I could see it not being as responsive, but I don't see the oil staying at a significantly lower temperature. Isn't that port connected to the main flow of oil to the head?
#28
Late to the party, but would that sensor location really stay cooler than the others. Its still in direct contact with oil, and I could see it not being as responsive, but I don't see the oil staying at a significantly lower temperature. Isn't that port connected to the main flow of oil to the head?
#35
Just to add a data point, I just got the oil temp sender and gauge from my old NA installed. Using a sandwich, with OT sender AT the adaptor itself. Oil gets up to temp pretty quickly (compared to my old 1.6L)-- the Oil warmer is working. I reach about 200 degrees in recent 70* ambients, and it only reaches up to 215 or so while idling or in heavy traffic.
#37
And yes, I don't expect it to reach very high temps in street use My old 1.6L only reaches 260* easily in a 20 minute session on track on a 90* ambient day but never got past 200* in Cali ambient temps.
#39
If you dont trust your sensor why not test the ******* thing directly? Unscrew that ****** from the engine and drop it in some boiling water if the gauge reads around 212°F then the gauge is right or at least close enough for the temp range you'll be using it in.
*Edit I missed a bunch of posts.
*Edit I missed a bunch of posts.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
slmhofy
Engine Performance
26
01-15-2018 09:25 PM
Chiburbian
Fabulous Fabrication
22
12-28-2015 12:33 AM