How to deck a 4 Cylinder Engine Block
#1
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2012
Location: Pensacola Fla.
Posts: 588
Total Cats: 203
How to deck a 4 Cylinder Engine Block
How to Deck a 4G63 Block
The block is a 7bolt 4G63T
The block was brought in to be prepped for rebuild.
It has been Bored and Honed to .020 over std.
Checking the block I found it had .0025 taper from front to back and has water pitting.
I set the block on the machine fixture; the block is on the main saddles.
I make a .0005 pass, Cyl #1 is shorter than Cyl # 4
I see I have a good level set up side to side, notice the dark low spots around #1 cylinder.
A MLS head gasket will not have had a good sealing surface.
[
Pass #2 is a .0015 cut
Still some pitting at the fire ring of the head gasket.
One more pass of .0015
The block looks good, and has a good head gasket sealing surface.
The block is a 7bolt 4G63T
The block was brought in to be prepped for rebuild.
It has been Bored and Honed to .020 over std.
Checking the block I found it had .0025 taper from front to back and has water pitting.
I set the block on the machine fixture; the block is on the main saddles.
I make a .0005 pass, Cyl #1 is shorter than Cyl # 4
I see I have a good level set up side to side, notice the dark low spots around #1 cylinder.
A MLS head gasket will not have had a good sealing surface.
[
Pass #2 is a .0015 cut
Still some pitting at the fire ring of the head gasket.
One more pass of .0015
The block looks good, and has a good head gasket sealing surface.
#4
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2012
Location: Pensacola Fla.
Posts: 588
Total Cats: 203
Guys... Thanks! Glad you like them!
I am tryin to post 1 a day for a bit.
If there is a specific machine shop procedure you would like to see , let me know and I will see what I can do for you.
I am tryin to post 1 a day for a bit.
If there is a specific machine shop procedure you would like to see , let me know and I will see what I can do for you.
#9
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
I'm digging that you are showing us the process. In fact, I've been digging a lot of your posts recently. If I had access to this information years ago, it could have saved me about $2k on a 5.0 rebuild that went to ---- due to a shitty machine shop. Keep up the good work!
^^ This. I'd love to build an engine, but I have no idea how to set clearances and crap for pistons and rings and bearings and oil pumps and blah blah blah ghjkasdenu... In my limited experience the machine work is not exactly super pricey, its the assembly that kills you.
^^ This. I'd love to build an engine, but I have no idea how to set clearances and crap for pistons and rings and bearings and oil pumps and blah blah blah ghjkasdenu... In my limited experience the machine work is not exactly super pricey, its the assembly that kills you.
#10
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2012
Location: Pensacola Fla.
Posts: 588
Total Cats: 203
Oscar... In my intro to this fourm, a customer pointed me here for his build that I am working on, so from grime to shine will be seen!
Devin &E02K Part of the reson I post this type of info is so the guys that have not built an engine know what to look for in a machine shop in there area. What the machining procedures are for diffrent parts. So then they can do the best build they can.
Soviet.. If I would have seen your post earlier, I would have got a pic so you could have seen how they set up, I just milled blcks today, 3 of them, Mitsu 4G63T, Honda H22A1 and a Mazda 1.8
Alta, you are right, everything is based off the mains, the set up I use for decking a block and boring a block, the machines require that the block is set up on the mains.
Devin &E02K Part of the reson I post this type of info is so the guys that have not built an engine know what to look for in a machine shop in there area. What the machining procedures are for diffrent parts. So then they can do the best build they can.
Soviet.. If I would have seen your post earlier, I would have got a pic so you could have seen how they set up, I just milled blcks today, 3 of them, Mitsu 4G63T, Honda H22A1 and a Mazda 1.8
Alta, you are right, everything is based off the mains, the set up I use for decking a block and boring a block, the machines require that the block is set up on the mains.
#17
I prefer these separate threads a lot more than one humongous thread about a full build.
The natural comments about each step in the process would make one complete thread pretty hard to navigate.
With individual threads of the steps one can always make a sticky linking them together.
Keep 'em coming
The natural comments about each step in the process would make one complete thread pretty hard to navigate.
With individual threads of the steps one can always make a sticky linking them together.
Keep 'em coming