Forged rods and stock pistons: semi-reliable on track?
#1
Senior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2008
Location: Falls Church, VA
Posts: 1,361
Total Cats: 17
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So I have my ABSURDflow parts, GT2860RS, TiAL EWG (0.5 bar spring; 7-8 psi), misc intercooler parts and the rest of the necessary stuff to install the turbo sitting in my basement ready to go on the car. I also have to change out the clutch if I’m to hold any power, drill & tap the pan for the oil return, and I figured I’d install a new rear main seal too. The plan is to pull the motor & tranny together to do that stuff.
The NoVA crew suggested that I install forged rods, you know, “while I have the motor out.” Not a bad idea but this is where the slope gets slippery. I mean, I can afford a set of rods, but I’m not looking to do a full motor build just yet. ****, even 200 whp is going to expose a lot of inadequacies on this car as soon as it sees the track again (brakes, various ducting, needs vented hood, etc) so I’m not shooting for 300+ hp just yet. I think I’d be happy at 225-250 whp for a while, as I re-learn how to drive and accumulate parts to build a motor and turn up the boost. I realize I will be running below the peak efficiency of the disco potato, but I didn’t want to have to buy another turbo for a while and also it was the smallest turbo that would work with V-bands.
It should be feasible to run that power on stock pistons I hope. So what exactly will I need to do? I was thinking M-tuned rods, (have a local machine shop check small end clearance and assemble onto pistons), new rod bearings, new rings, new HG, light hone of the cylinders with a bore brush. Will that about do it?
I also have enough $ in the wife-doesn’t-know-about-it stash to pick up a 6-spd. That and forged rods ought to let me drive it home from the track after pwning noobs, right?
Basically I’m trying to decide between two choices:
1. Install the turbo parts, keep stock internals & 5-spd, run low boost, maybe **** won’t blow up.
2. Drop the money on rods & 6-speed, but will I be able to track it *reliably* at say 250 whp with a conservative tune?
Option 3 (fully built motor) is out because I will also need to drop coin elsewhere on the car and if I wait to save up enough to do everything at once, I’ll never get this turbo installed.
The NoVA crew suggested that I install forged rods, you know, “while I have the motor out.” Not a bad idea but this is where the slope gets slippery. I mean, I can afford a set of rods, but I’m not looking to do a full motor build just yet. ****, even 200 whp is going to expose a lot of inadequacies on this car as soon as it sees the track again (brakes, various ducting, needs vented hood, etc) so I’m not shooting for 300+ hp just yet. I think I’d be happy at 225-250 whp for a while, as I re-learn how to drive and accumulate parts to build a motor and turn up the boost. I realize I will be running below the peak efficiency of the disco potato, but I didn’t want to have to buy another turbo for a while and also it was the smallest turbo that would work with V-bands.
It should be feasible to run that power on stock pistons I hope. So what exactly will I need to do? I was thinking M-tuned rods, (have a local machine shop check small end clearance and assemble onto pistons), new rod bearings, new rings, new HG, light hone of the cylinders with a bore brush. Will that about do it?
I also have enough $ in the wife-doesn’t-know-about-it stash to pick up a 6-spd. That and forged rods ought to let me drive it home from the track after pwning noobs, right?
Basically I’m trying to decide between two choices:
1. Install the turbo parts, keep stock internals & 5-spd, run low boost, maybe **** won’t blow up.
2. Drop the money on rods & 6-speed, but will I be able to track it *reliably* at say 250 whp with a conservative tune?
Option 3 (fully built motor) is out because I will also need to drop coin elsewhere on the car and if I wait to save up enough to do everything at once, I’ll never get this turbo installed.
#2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Honestly it sounds like you have a pretty good plan. Stock pistons will work fine. Do a quick and dirty hone, make sure you get all the gunk out of the ringlands and put on new rings, new bearings (rod and main...might as well) and you should be set to pwn some newbs. Just be kind of conservative with your tune and dont detonate and you'll be fine.
Edit: My current engine has 323 GTX rods (beefier than miata) and stock pistons. All I did was swap the crank for a long nose, new bearings, used pistons and new rings. Hell, I didn't even hone the bores and there were a few light scratches on a couple of the cylinder walls. Runs real strong.
Edit: My current engine has 323 GTX rods (beefier than miata) and stock pistons. All I did was swap the crank for a long nose, new bearings, used pistons and new rings. Hell, I didn't even hone the bores and there were a few light scratches on a couple of the cylinder walls. Runs real strong.
#3
2 Props,3 Dildos,& 1 Cat
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
two common failure modes you'll find in a stock piston are melting and breaks at the thin sections around the perimeter.
generally these are caused by detonation. the forged pistons will succumb to it as well but the strength helps resist it to some degree.
one thing you can do to help keep heat out of the piston is a thermal barrier coating on the tops. you can send them somewhere (swain, replika maschinen, etc) or you can buy the **** from tech line and DIY coat them.
and of course, a conservative tune helps.
generally these are caused by detonation. the forged pistons will succumb to it as well but the strength helps resist it to some degree.
one thing you can do to help keep heat out of the piston is a thermal barrier coating on the tops. you can send them somewhere (swain, replika maschinen, etc) or you can buy the **** from tech line and DIY coat them.
and of course, a conservative tune helps.
#4
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
this place charges $30 a position for a tri-coat: http://www.performancecoatings.com/index2.html
IIRc, Levnubhin has used them.
First by impregnation of the skirts, pin bores and ring area with a dry film coating, reducing the effects of piston scuffing, piston rock and other friction induced problems.
Next, the piston dome is coated with a Ceramic thermal barrier to distribute heat evenly across the piston dome and increase combustion temperatures.
Finally, the underside of the piston is coated with a thermal barrier. This process evenly distributes heat in the chamber, thereby greatly diminishing or eliminating the chance of detonation, while reducing oil cling.
Next, the piston dome is coated with a Ceramic thermal barrier to distribute heat evenly across the piston dome and increase combustion temperatures.
Finally, the underside of the piston is coated with a thermal barrier. This process evenly distributes heat in the chamber, thereby greatly diminishing or eliminating the chance of detonation, while reducing oil cling.
#6
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
this place charges $30 a position for a tri-coat: http://www.performancecoatings.com/index2.html
#7
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
It should be feasible to run that power on stock pistons I hope. So what exactly will I need to do? I was thinking M-tuned rods, (have a local machine shop check small end clearance and assemble onto pistons), new rod bearings, new rings, new HG, light hone of the cylinders with a bore brush. Will that about do it?
2. Drop the money on rods & 6-speed, but will I be able to track it *reliably* at say 250 whp with a conservative tune?
2. Drop the money on rods & 6-speed, but will I be able to track it *reliably* at say 250 whp with a conservative tune?
Got a fresh set of 9.1:1 pistons from a 94-97+ m-tuned rods+new bearings/seals/gaskets+ hone+rings.
Been running like a champ at around 250whp for a while now, and shooting for 300+ pretty soon here.
As long as you keep the tune safe AND/OR use something to help keep temps down/detonation away (w/i or e85) and keep the car well cooled (re-route and possibly bigger aluminum rad) I don't see a reason why it wouldn't be solid at 250whp.
EVEN if tracked.
#10
Senior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2008
Location: Falls Church, VA
Posts: 1,361
Total Cats: 17
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Well the least amount of power I'll be running is [whatever a 2860 supports at 0.5 bar of boost]. Just a quick look at a compressor map has me guessing that's somewhere around 200 hp? I am capable of self-restraint and having to drive the car home from the track tends to impart a sense of mechanical empathy. I could simply refuse to allow myself to buy an MBC.
OTOH, I will eventually need forged rods. When I do a full motor build sometime down the road I should be able to reuse the rods, so the only money I will be losing if I do just the rods now would be the cost of one round of bearings, rings and some gaskets. I can live with that if it will mean the motor is reliable for 12-18 months while letting me run closer to ~250 hp.
If I buy a set of Beck-Arnley or Sealed Power rings for the stock bore size, will I have to mess with sizing the rings or will they be fine to just drop in? Likewise, should I expect a set of stock 1.8 bearings to just drop in? Plastigauging the bearings to check clearances is probably within my realm of capability, not sure about sizing piston rings though. I'm trying to minimize how much $ I have to pay a shop to do, or at least know what to expect.
OTOH, I will eventually need forged rods. When I do a full motor build sometime down the road I should be able to reuse the rods, so the only money I will be losing if I do just the rods now would be the cost of one round of bearings, rings and some gaskets. I can live with that if it will mean the motor is reliable for 12-18 months while letting me run closer to ~250 hp.
If I buy a set of Beck-Arnley or Sealed Power rings for the stock bore size, will I have to mess with sizing the rings or will they be fine to just drop in? Likewise, should I expect a set of stock 1.8 bearings to just drop in? Plastigauging the bearings to check clearances is probably within my realm of capability, not sure about sizing piston rings though. I'm trying to minimize how much $ I have to pay a shop to do, or at least know what to expect.
#11
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
In my experience (albeit limited) gapping rings is easier than plastigauge, but that's just my preference. You really should check the ring clearances. It's just good practice at the very least. I second the 'just wait' idea though. Tearing apart a motor isn't exactly an easy or quick task. Might as well just wait until you can afford a set of pistons and do it all at once.
#12
Elite Member
iTrader: (8)
Join Date: Dec 2008
Location: Kingston, Ontario
Posts: 2,910
Total Cats: 51
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
to get 250hp you will be around 0.7bar.
my old setup (1.6) was making 225whp at 12psi with 2860 0.86
completely stock 1.6 with mods below (with 2860)
im also down for the just wait. that is my plan as i hope to hit 1.8bar next year on my built engine and unleash the power.
my old setup (1.6) was making 225whp at 12psi with 2860 0.86
completely stock 1.6 with mods below (with 2860)
im also down for the just wait. that is my plan as i hope to hit 1.8bar next year on my built engine and unleash the power.
#14
Elite Member
iTrader: (15)
Join Date: Sep 2007
Location: Incline Village, NV
Posts: 2,034
Total Cats: 5
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I would do it, i've gone through to many motors not to install rods in a boosted miata motor.
If i were to do it all over again i would have spend the extra time on a quality motor right off the bat and just kept the boost low until i wanted more power. Which wont take long on the 2860.
If i were to do it ALL over again, i would have gone v8 right from the beginning though.
If i were to do it all over again i would have spend the extra time on a quality motor right off the bat and just kept the boost low until i wanted more power. Which wont take long on the 2860.
If i were to do it ALL over again, i would have gone v8 right from the beginning though.
#16
Tour de Franzia
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Oh, and I made 254whp on a dynojet at 10psi 8* back from MBT; at 13psi I'm making 260whp on a DynoDynamics.. You're going to be way under the prime with that turbo and might want to consider a smaller AR to help wake-up the turbo a bit.
#17
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
The reason we suggested rod to Scott was because he's going to pull the motor and trans to do his turbo kit since he's doing the clutch at the same time.
We figure rods are cheap and easy to do while the motor is out...no urgency for pistons if his tune is good.
We figure rods are cheap and easy to do while the motor is out...no urgency for pistons if his tune is good.
#19
Senior Member
Thread Starter
iTrader: (4)
Join Date: Jan 2008
Location: Falls Church, VA
Posts: 1,361
Total Cats: 17
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So even at low boost the 2860 is making decent power with conservative timing. Stock pistons ought to hold up to that, so as long as I have the 6-spd and rods that won't bend I can at least avoid totally cutting off the turbo at its knees.
BTW, 8* back from MBT was how much back from detonating?
I've been reading today on bearing & ring sizing and it doesn't look that difficult really. ACL Race bearings for the rods are like $42. The motor runs like a top and I have no oil pressure issues so I'm not inclined to touch the main bearings or spend the extra $90 on them considering they don't seem to be a common failure point at this power level. Fresh piston rings in standard size are $100 for Sealed Power, half that for Rock brand and Beck-Arnley is priced in between. Plastigauge is cheap and I'm pretty sure somebody local will let me borrow a honing brush. Add $50 for a HG, a few bucks to buy some tools I don't already own and doing "just the rods" will probably cost $500-600. That's not too bad considering the big bump in reliability.
#20
mkturbo.com
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,189
Total Cats: 1,685
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Living below prime efficiency >>> spending $3xx on another turbine housing.
So even at low boost the 2860 is making decent power with conservative timing. Stock pistons ought to hold up to that, so as long as I have the 6-spd and rods that won't bend I can at least avoid totally cutting off the turbo at its knees.
BTW, 8* back from MBT was how much back from detonating?
I've been reading today on bearing & ring sizing and it doesn't look that difficult really. ACL Race bearings for the rods are like $42. The motor runs like a top and I have no oil pressure issues so I'm not inclined to touch the main bearings or spend the extra $90 on them considering they don't seem to be a common failure point at this power level. Fresh piston rings in standard size are $100 for Sealed Power, half that for Rock brand and Beck-Arnley is priced in between. Plastigauge is cheap and I'm pretty sure somebody local will let me borrow a honing brush. Add $50 for a HG, a few bucks to buy some tools I don't already own and doing "just the rods" will probably cost $500-600. That's not too bad considering the big bump in reliability.
So even at low boost the 2860 is making decent power with conservative timing. Stock pistons ought to hold up to that, so as long as I have the 6-spd and rods that won't bend I can at least avoid totally cutting off the turbo at its knees.
BTW, 8* back from MBT was how much back from detonating?
I've been reading today on bearing & ring sizing and it doesn't look that difficult really. ACL Race bearings for the rods are like $42. The motor runs like a top and I have no oil pressure issues so I'm not inclined to touch the main bearings or spend the extra $90 on them considering they don't seem to be a common failure point at this power level. Fresh piston rings in standard size are $100 for Sealed Power, half that for Rock brand and Beck-Arnley is priced in between. Plastigauge is cheap and I'm pretty sure somebody local will let me borrow a honing brush. Add $50 for a HG, a few bucks to buy some tools I don't already own and doing "just the rods" will probably cost $500-600. That's not too bad considering the big bump in reliability.