99 mazda miata, Hard to start, shaken engine after head gasket replacement ~!
#21
I would take both of them to a machine shop and see what they say. It's good that you have another set of shims, springs and valves to work with. I don't think it would cost more than $50 bucks to get both heads checked out, our local shop only charges me $20 for a head inspection.
The problem with having zero clearence between the cam and the tappet is that it's not allowing the valves to fully close and besides causing poor running condition, it's also not allowing the valves to cool properly by not allowing them to rest fully on the seats. Who knows what happened to this head before you got it, you know?
The problem with having zero clearence between the cam and the tappet is that it's not allowing the valves to fully close and besides causing poor running condition, it's also not allowing the valves to cool properly by not allowing them to rest fully on the seats. Who knows what happened to this head before you got it, you know?
#22
so i should take both head to a machine shop and ask for valve clearance?
Thanks for advices
Thanks for advices
I would take both of them to a machine shop and see what they say. It's good that you have another set of shims, springs and valves to work with. I don't think it would cost more than $50 bucks to get both heads checked out, our local shop only charges me $20 for a head inspection.
The problem with having zero clearence between the cam and the tappet is that it's not allowing the valves to fully close and besides causing poor running condition, it's also not allowing the valves to cool properly by not allowing them to rest fully on the seats. Who knows what happened to this head before you got it, you know?
The problem with having zero clearence between the cam and the tappet is that it's not allowing the valves to fully close and besides causing poor running condition, it's also not allowing the valves to cool properly by not allowing them to rest fully on the seats. Who knows what happened to this head before you got it, you know?
#23
you cant set the valve clearance properly with the head unbolted from the car. with that said. check the clearances and set them accordingly. if it still runs like crap after that do a compression test. if its low pull the head and pour water/brake kleen into the runners when the valves are closed. this will show you if you have a bent valve or not.
#24
http://youtu.be/rmEtGkpg2SQ
this is how i checked the gap, but no luck, it cant fit the thinnest feeler
this is how i checked the gap, but no luck, it cant fit the thinnest feeler
you cant set the valve clearance properly with the head unbolted from the car. with that said. check the clearances and set them accordingly. if it still runs like crap after that do a compression test. if its low pull the head and pour water/brake kleen into the runners when the valves are closed. this will show you if you have a bent valve or not.
#26
I watched the vid... You used a .010.. thats a bit thick to start.. get a feeler gauge set that has .003, .005, .007
Also if the machinist or the engine builder was sharp, he may have set the lash up a bit tight so the cam wouls appere a tad larger.
So if you find .006 lash on the intake and as tight as .007/.008 on the exhaust it will be ok.
I say this since your .010 would not fit down either bank of pucks
And try again
Twibs.... what can you not set the lash with the head off the engine?
I must have been doing it wrong all these years.....
Also if the machinist or the engine builder was sharp, he may have set the lash up a bit tight so the cam wouls appere a tad larger.
So if you find .006 lash on the intake and as tight as .007/.008 on the exhaust it will be ok.
I say this since your .010 would not fit down either bank of pucks
And try again
Twibs.... what can you not set the lash with the head off the engine?
I must have been doing it wrong all these years.....
#27
i bought the feeler guages from auto zone
http://www.autozone.com/autozone/acc...fier=1931_0_0_
the thinnest one is 0.010 254mm.
i am going to get something thinner tomorrow.
http://www.autozone.com/autozone/acc...fier=1931_0_0_
the thinnest one is 0.010 254mm.
i am going to get something thinner tomorrow.
I watched the vid... You used a .010.. thats a bit thick to start.. get a feeler gauge set that has .003, .005, .007
Also if the machinist or the engine builder was sharp, he may have set the lash up a bit tight so the cam wouls appere a tad larger.
So if you find .006 lash on the intake and as tight as .007/.008 on the exhaust it will be ok.
I say this since your .010 would not fit down either bank of pucks
And try again
Twibs.... what can you not set the lash with the head off the engine?
I must have been doing it wrong all these years.....
Also if the machinist or the engine builder was sharp, he may have set the lash up a bit tight so the cam wouls appere a tad larger.
So if you find .006 lash on the intake and as tight as .007/.008 on the exhaust it will be ok.
I say this since your .010 would not fit down either bank of pucks
And try again
Twibs.... what can you not set the lash with the head off the engine?
I must have been doing it wrong all these years.....
#30
im sure it changes but to what degree. a few hundred thou? i dunno. but for all we know op didnt clean the block or head good when putting a new hg on. did he put a new hg on? and do the feeler gauges fit any of the lobes? it would be strange if all the valves were tighter than .254mm/.010in as the exhaust side should have more clearance than that.
#31
I have personally set exhaust lash tighter that .010, it can add a few degrees of duration and a tad more lift.
Since the op seems to have bought a built head, it would not be uncommon to find tighter than stock lash settings.
Now if he is .003 intake and .005 exhaust.. to me, thats a bit too tight.....
Since the op seems to have bought a built head, it would not be uncommon to find tighter than stock lash settings.
Now if he is .003 intake and .005 exhaust.. to me, thats a bit too tight.....
#32
I have personally set exhaust lash tighter that .010, it can add a few degrees of duration and a tad more lift.
Since the op seems to have bought a built head, it would not be uncommon to find tighter than stock lash settings.
Now if he is .003 intake and .005 exhaust.. to me, thats a bit too tight.....
Since the op seems to have bought a built head, it would not be uncommon to find tighter than stock lash settings.
Now if he is .003 intake and .005 exhaust.. to me, thats a bit too tight.....
finally i bought the right feeler gauges.
Below is the numbers that i got. Do they look right?
Intake: 0.06 / 0.07 / 0.07 / 0.09 / 0.07 / 0.08 / 0.08 / 0.08
Exhaust: 0.08 / 0.09 / 0.08 / 0.07 / 0.06 / 0.09 / 0.10 / 0.07
It looks like exhaust side is a bit too tight, right?
Thread
Thread Starter
Forum
Replies
Last Post
Jike Spingleton
Cars for sale/trade
3
09-20-2016 04:33 PM