When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
To quote the LC-2 manual: "Using a clock as reference, mount the bung between the 9:00 o’clock and 3:00 o’clock position. Welding the bung in the lower section of the exhaust pipe can result in sensor damage caused by condensation making contact with the sensor’s internal heating element."
It looks like your sensor is lower than 3:00 o'clock.
I remember specifically emailing for them to make sure it was welded between 9 and 3 oclock... =[
Something has to be wrong...<br />
<br /><br />
<br />Mine is 6" from turbo outlet, been using the same sensor for 5 years with no issue. Sensor in the 12 oclock position, using an LC-1, not an MTX-L.
<br />
<br /><br />
<br />I call bullshit, you don't have a turbo car
Fuel additives, poor grounding, oil additives, cleaners and solvents, some rtv silicones, overly high temp, overly low temp, overly rich, and a few other things can contribute to early failure, iirc.
Fuel additives, poor grounding, oil additives, cleaners and solvents, some rtv silicones, overly high temp, overly low temp, overly rich, and a few other things can contribute to early failure, iirc.
Never used additives in the fuel or oil.
Grounded MS and WB to the battery.
Haven't rtv'd anything.
Afr is 11.5 -11.8 or so in boost.
I don't have an egt setup to tell temps...
The sensor I put in without a heat sync 9/1 lasted till this week. I had the rest of the exhaust finished and we put a bung at 12 oclock, allllll the way back pretty much by the diff. It's a 1" bung too so the sensor is barely in the exhaust stream now. If this doesn't last, I'm out of ideas.
I had the same problem. When I first got mine it acted up with e8 error. Mine is naturally aspirated. Few weeks later it now works good. (Litttle rich or little lean) I had to reset it and pull it out a couple of times. Best thing is to do is go further down the exhaust pipe with a heat sinksince you have forced induction. Require some welding
Got another E8 today. Called innovate and the guy said something has to be damaging the sensors and there's no way it can be a problem with the controller because replacing the sensor fixes the problem for a little bit.
I do have one piece of info I wasn't aware of: I have the controller powered by a wire coming from the ignition switch (white/red), hot when key on obviously, but Innovate said that's not good enough and should be on its own power circuit. However, he suggested this would not cause an E8, but it should be changed.
I connected to the controller today and updated the firmware, and did a calibration so we'll see what happens...
@Mech5700, did you ever work out what the cause of the E8 error codes was? I've been tuning my MS on my naturally aspirated 1994 1.8 with the wideband sensor installed in the stock O2 sensor location and just ran into an E8 while cruising around the neighborhood, not running overly rich or lean leading up to the E8. I had less than 10 hours running the sensor on the car, so it seems strange that I could have run into an E8 so quickly. I hear mixed reviews of the Innovate MXT-L that I'm using, so I'm just trying to figure out what the source of the issue may be.
Called innovate and the guy said something has to be damaging the sensors and there's no way it can be a problem with the controller because replacing the sensor fixes the problem for a little bit..
that's complete BS. the controller CAN, and if designed by monkeys and built with cheap components WILL contribute to premature sensors death.
Dwalk51, Nope, never got to the bottom of it. The E8's come back, sometimes weeks after a new sensor is installed, sometimes months. I think this last one was maybe a week before it set the E8 again. I got so fed up with it that I disconnected my gauge so it doesn't sit there and flash at me 7.4... (my tune is decent enough so I don't really NEED EGO correction at this point)
ldslds88, I think I am going to get a 14point7 and a gauge from Speedhut. I don't have anything against AEM, they just don't have a gauge that will look right with my setup.
Speedhut gauges can be customized and I hear really good things about 14point7...just gotta stop bein lazy and buy stuff lol.
wow a thread necro that got a response from the OP... internet's not what it used to be
reading through the post though I don't think its the sensor location (not since you moved it). I have been researching O2 placement and the short sensor life you have (and still are I guess) getting is very abnormal. A lot of Suby guys run theirs a hell of a lot closer (a lot of their aftermarket DPs have them installed really close apparently) with no issues. I'm not sure what could be causing it (sounds like you tried everything) but I think your placement is fine now...