When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
NB1 99 motor with wiseco pistons and eagle rods, acl bearings and arp studs.
Coolant reroute form skidnation. And thermostat 180F
Completely stock head.
Custom equal length tubular top mount exhaust mani
Gtx 2867 gen1 IWG with a turbosmart twinport actuator
R8 ignition coils custom wiring harness for wasted spark. ( ms2pnp does not support sequential spark)
Custom 3 inch downpipe and 3 inch exhaust.
Energy intercooler 2inch inlet 2.5 inch outlet.
hks ssqv bov
MS2pnp
AEM AFR
Prosport gauges for boost and water temp
APEXi AVCR boost controller
Walboro 255
New id 1050x injectors
Fuelab FPR with stock fuel rail.
6speed with a stock 1.8 flywheel and a custom 6 puck cluch
Torsen diff with a 3.6.
Bilstein pss9
TSE 11.75'' 4piston dynapro BBK
JR 19 wheels 16'' with 595 RS-R.195 front and 205 rear.
Roll bar, frame rails, Racing beat front and rear anti-roll bars,BeatRush PPF brace.
Carbon miata hood and trunk
A quick release deep dish steering wheel and a gutted driver's seat. I am 6.1
Power steering and A/C working good
Thanks for the details. I'm a fellow GTX2867R owner and think I may have been making slightly more power than the virtual dyno predicted. This may explain the damaged 6 speed I'm going to have to change.
Thanks for the details. I'm a fellow GTX2867R owner and think I may have been making slightly more power than the virtual dyno predicted. This may explain the damaged 6 speed I'm going to have to change.
No prob m8. Happy to give back for all the reading i have done here
What Hotside do you have? Mine is .64. How much boost do you run?
After 20 edits... I cannot get it to embed... Aaaaaaand... now it works, you just paste the whole desktop URL in and it does it automatically..
So its an Absurdflow style low mount, 3" system with cat and mufflers, ebay intercooler 210mm tall, same one as used in MSM's but 210 instead of 140mm tall. ID1300s, and we taper the boost on to keep peak torque around 300-320ftlb. I think this was a 3000-8000rpm run.
It is a dead stock VVT. 10:1 supertechs, supertech heavy doubles, Manley Rods, Boundary Stage 2, and ATI damper. Pump E85.
Outside of that Ill show you photos of the bolt ons and the timing table. Dyno is an oldschool analog Dyno Dynamics, in shootout mode, however shootout is supposed to have the temp sensor at the filter and we always run it just in the room.
Ignore that circle, just had that pic and thought I would share the downpipe design (it's a different engine and stuff but the same manifold and downpipe). And yes, internal gate. And yes, it really has a cat and muffler etc
I have an EFR 6758 waiting to go in so i will have a Garrett Vs BW in the near future.
FYI: most people on this site mention horsepower at the wheels - which is 248,2 in your case. Europeans are more used to horsepower at the crank (i.e. horsepower at wheels with a correction).
FYI: most people on this site mention horsepower at the wheels - which is 248,2 in your case. Europeans are more used to horsepower at the crank (i.e. horsepower at wheels with a correction).
So you think his 328 is 248? That's quite a lot of correcting.
Think so. The greek word τροχού means wheel. Agreed that is seems like a pretty significant correction - 20-25% seems to be more common.
I am not going to discuss about hp to the crank or to the wheels. The correction factor is way off.
328 on 16.5 psi is a normal number for this turbo Imho. I dont think that garrett's declaired hp number for the gen1 gtx2867 wich is rated for max 470 if i remember correctly, is whp. It is 470HP.
Soooo when guys here output 415 whp on a 6258BW with a .64 turbine housing which is rated for max 450hp(not WHP) that sound right to you?