Where not to skimp?
#21
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (5)
Join Date: Oct 2011
Location: Detroit (the part with no rules or laws)
Posts: 5,683
Total Cats: 805
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Should have not dicked with a SPEC clutch, and went FM from the start.
Should have not bought a used MSII, and built my own, or had one built just for me.
Should have used more braided lines, i destory the rubber oil return every time.
Should have paid more for an intercooler that FITS, instead of screwing with ebay.
Should have done more research on brake pads.
Not a bad list of mine for my first time around.
Should have not bought a used MSII, and built my own, or had one built just for me.
Should have used more braided lines, i destory the rubber oil return every time.
Should have paid more for an intercooler that FITS, instead of screwing with ebay.
Should have done more research on brake pads.
Not a bad list of mine for my first time around.
#22
Elite Member
iTrader: (12)
Join Date: Nov 2009
Location: Harpers Ferry WV
Posts: 1,516
Total Cats: 20
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Should have used the correct computer to begin with
Should not have listened to the so called "expert" that was helping me
Should have planned out my build better to start so I did not have to redo a bunch.
Should not have listened to the so called "expert" that was helping me
Should have planned out my build better to start so I did not have to redo a bunch.
#23
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Should have just kept my first MX-5 (MSM) instead of selling it for a 1990 which I then fitted a JRSC, sold that for another MSM, sold that for JRSC equipped NB that lunched its engine due to a bad tune, sold that to buy my current car which I have built the engine and turbocharged. That's a fair bit of wasted coin...
#24
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Should have never bought somebody elses project
Condition of body is most important
hardtop is a must have
creature comforts are important a/c, p/s
Ms-1 is headache inducing
coolant reroute is the way to go the first time
stretching turbo studs/bolts in the middle of a highway run sucks
dont forget that little mounting stud for the heater lines when doing a water pump
Condition of body is most important
hardtop is a must have
creature comforts are important a/c, p/s
Ms-1 is headache inducing
coolant reroute is the way to go the first time
stretching turbo studs/bolts in the middle of a highway run sucks
dont forget that little mounting stud for the heater lines when doing a water pump
#31
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My input, don't permanently modify a desirable '94 in order to fit piping and intercooler. Spend the extra time to make the parts fit the car, don't make the car fit the parts.
#34
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
OP, do you mean where not to skimp in terms of a turbo build or in the car in general?
Car in general:
Roll bar
Tires
Suspension
Brakes
I'd also start with a '94+ that has a torsen and a nice body with good paint too. And a six speed can't hurt.
If you mean where not to skimp on the turbo build, I'd say make sure you go with a standalone ECU if you can (this assumes you live outside California), stay away from bandaids.
Car in general:
Roll bar
Tires
Suspension
Brakes
I'd also start with a '94+ that has a torsen and a nice body with good paint too. And a six speed can't hurt.
If you mean where not to skimp on the turbo build, I'd say make sure you go with a standalone ECU if you can (this assumes you live outside California), stay away from bandaids.
#36
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
^ this
Also agree with 1.8 > 1.Fail. I motor swapped a 1.6 for a 1.6 and now i'm 1.8. Should have done 1.8 the first time around. Also agree with starting platform. I should have waited and payed more to start with a good shape 94 or 95 with torsen. I see them on craigslist now and always think how much better it would have been to start on that platform. It totally would have been worth the extra $1-2k.
In most states obd2 emissions test aren't required on vehicles till 96.
Also agree with 1.8 > 1.Fail. I motor swapped a 1.6 for a 1.6 and now i'm 1.8. Should have done 1.8 the first time around. Also agree with starting platform. I should have waited and payed more to start with a good shape 94 or 95 with torsen. I see them on craigslist now and always think how much better it would have been to start on that platform. It totally would have been worth the extra $1-2k.
In most states obd2 emissions test aren't required on vehicles till 96.
#37
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Don't cheap out on:
- Oil and water lines for your turbo! Get braided or hard lines - so much heat there that rubber doesn't really hold up. I had a few water lines split before I wised up.
- Suspension - most people here are on their 2nd or 3rd setup (I'm on my 3rd). Do it right the first time. And by "right", think about how you are going to use your car. For a street car you can get away with AGX/ Ground Controls. For a track car, sky's the limit.
- Wheel and tire setup - same as suspension. You can buy 15x7s, then upgrade to 15x8s, then get 15x9s....or just get the 15x9s straightaway. One of these days somebody is going to make a street tire that can take full advantage of the 9s width (fingers crossed for a 245/40/15 Hankook RS3).
Things I did right despite my naivety:
- Bought a 1.8 car that already had a roll bar, ultrashields, hardtop, and torsen but only had two track days on the build. Oh, and had enough Jackson Racing NA parts (intake, header, exhuast) to halfway fund my turbo kit. Dude had $10k in receipts (including the $4k he paid for the car).
- Oil and water lines for your turbo! Get braided or hard lines - so much heat there that rubber doesn't really hold up. I had a few water lines split before I wised up.
- Suspension - most people here are on their 2nd or 3rd setup (I'm on my 3rd). Do it right the first time. And by "right", think about how you are going to use your car. For a street car you can get away with AGX/ Ground Controls. For a track car, sky's the limit.
- Wheel and tire setup - same as suspension. You can buy 15x7s, then upgrade to 15x8s, then get 15x9s....or just get the 15x9s straightaway. One of these days somebody is going to make a street tire that can take full advantage of the 9s width (fingers crossed for a 245/40/15 Hankook RS3).
Things I did right despite my naivety:
- Bought a 1.8 car that already had a roll bar, ultrashields, hardtop, and torsen but only had two track days on the build. Oh, and had enough Jackson Racing NA parts (intake, header, exhuast) to halfway fund my turbo kit. Dude had $10k in receipts (including the $4k he paid for the car).
#39
Moderator
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/moderator.png)
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,885
Total Cats: 3,075
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Many of my problems often stemmed from improper heat shielding initially including a melted dipstick handle that cost me an oil pump.
I also unfortunately learned that oil lines can be made of material inside that may not actually be suited for oil or high temperatures. Local hydraulic shop guy's fault on that one cost me a turbo.
#40
Elite Member
iTrader: (7)
Join Date: Jan 2007
Location: Renton Washington
Posts: 1,731
Total Cats: 4
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Don't buy a shell. Don't get me wrong it was a fun experience putting together a car that had only interior wiring harness and tires. I learned quite a bit from it. However it costed me more in the long run instead of buying a good running Torsen Miata with all the body panels from the get go. Buying body panels over the internet also blows. Ebay steering wheels/hubs are cheap and you can literally bend them with your fist.
Other than that its been a fun time. Ive built a few turbo setups and enjoyed it. My next Miata is going to be an NB though for a little bit more comfort and a whole lot more power (built 1.8) but that's way down the road after i get my Engineering degree. Most important lesson is the one you learn from =)
Other than that its been a fun time. Ive built a few turbo setups and enjoyed it. My next Miata is going to be an NB though for a little bit more comfort and a whole lot more power (built 1.8) but that's way down the road after i get my Engineering degree. Most important lesson is the one you learn from =)