New ID725CC injectors - fuel rail not sitting flush... WTF? SOLVED!
#1
Elite Member
Thread Starter
Join Date: Mar 2006
Location: Schwarzenberg, Germany
Posts: 1,557
Total Cats: 103
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Hi,
it's days like these that make me sometimes wish I would have a non-DIY car...
I installed my new ID 725CC injectors today, but my fuel rail is not sitting flush on the "bosses" (?) when I install it. See attached pictures...
I installed the spacers at the fuel rail - but when I tighten the rail, the rail just goes flush on the top of the holding boss, not at the bottom, there are ~2mm missing... WTF? All the injectors are properly seated...
Please help me out - what could I possibly be doing wrong?
Did anyone else have this problem?
Car is a B6 with DIY Dual-feed fuel rail...
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55445-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_02.jpg?dateline=1348306268)
See the angle at which the fuel rail is sitting:
Injectors:
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55448-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_06.jpg?dateline=1348306268)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55449-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_07.jpg?dateline=1348306268)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55450-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_08.jpg?dateline=1348306268)
![vash](https://www.miataturbo.net/images/smilies/vash.gif)
![vash](https://www.miataturbo.net/images/smilies/vash.gif)
it's days like these that make me sometimes wish I would have a non-DIY car...
I installed my new ID 725CC injectors today, but my fuel rail is not sitting flush on the "bosses" (?) when I install it. See attached pictures...
I installed the spacers at the fuel rail - but when I tighten the rail, the rail just goes flush on the top of the holding boss, not at the bottom, there are ~2mm missing... WTF? All the injectors are properly seated...
Please help me out - what could I possibly be doing wrong?
Did anyone else have this problem?
Car is a B6 with DIY Dual-feed fuel rail...
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55445-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_02.jpg?dateline=1348306268)
See the angle at which the fuel rail is sitting:
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55446-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_04.jpg?dateline=1348306268)
Injectors:
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55447-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_05.jpg?dateline=1348306268)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55448-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_06.jpg?dateline=1348306268)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55449-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_07.jpg?dateline=1348306268)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55450-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_08.jpg?dateline=1348306268)
![vash](https://www.miataturbo.net/images/smilies/vash.gif)
![vash](https://www.miataturbo.net/images/smilies/vash.gif)
![vash](https://www.miataturbo.net/images/smilies/vash.gif)
Last edited by Zaphod; 09-23-2012 at 11:50 AM.
#6
Elite Member
Thread Starter
Join Date: Mar 2006
Location: Schwarzenberg, Germany
Posts: 1,557
Total Cats: 103
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Just checked at ILMotorsport - they are the same for all Miatas, NA, NB, NBFL.
I checked them by eye with my old 460cc RX-7 injectors and they seem to match.
#11
Elite Member
Thread Starter
Join Date: Mar 2006
Location: Schwarzenberg, Germany
Posts: 1,557
Total Cats: 103
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I already took pictures of the injectors, but don't have them at hand atm.
But I think this could be it. There are little rubber gromets, about half the size of the rubber isolators above them. The gromets have a conical shape. I post the pics asap.
How would one get the gromets of the pintle ends? Just pull? They do look fixed on the metall...?
Thanks
But I think this could be it. There are little rubber gromets, about half the size of the rubber isolators above them. The gromets have a conical shape. I post the pics asap.
How would one get the gromets of the pintle ends? Just pull? They do look fixed on the metall...?
Thanks
#13
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
What method did you use to install the injectors/rail? I just installed a set yesterday on mine, I did the following:
Removed old injectors, all 3 seals came out with each of my factory injectors.
Cleaned out the manifold area where the injectors seat, there was some dust/grime buildup in each of the holes.
Put on all 3 new seals on each injector and applied liberal amounts of clean oil to each.
Slid the new injectors into the fuel rail.
Installed the fuel rail with new injectors as a unit into the manifold.
Once installed, I inspected the bottom grommet of each to insure it properly seated without pinching the rubber seal.
Rotated each injector to make sure none were binding in any manner.
Finally I snugged down the bolts to hold it in.
This is probably worthless info, but it's what I did and things are working great for me with no leaks.
I was a little surprised how obnoxious the install was. Easy, but annoying. I kept thinking to myself how many curse words I'm going to use next year when I have to change back to stock for emissions inspection, then change back again once it's over.
Removed old injectors, all 3 seals came out with each of my factory injectors.
Cleaned out the manifold area where the injectors seat, there was some dust/grime buildup in each of the holes.
Put on all 3 new seals on each injector and applied liberal amounts of clean oil to each.
Slid the new injectors into the fuel rail.
Installed the fuel rail with new injectors as a unit into the manifold.
Once installed, I inspected the bottom grommet of each to insure it properly seated without pinching the rubber seal.
Rotated each injector to make sure none were binding in any manner.
Finally I snugged down the bolts to hold it in.
This is probably worthless info, but it's what I did and things are working great for me with no leaks.
I was a little surprised how obnoxious the install was. Easy, but annoying. I kept thinking to myself how many curse words I'm going to use next year when I have to change back to stock for emissions inspection, then change back again once it's over.
![rofl](https://www.miataturbo.net/images/smilies/rofl1.gif)
#14
Elite Member
Thread Starter
Join Date: Mar 2006
Location: Schwarzenberg, Germany
Posts: 1,557
Total Cats: 103
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
O.k. Injectors are in, the rubber gromets were the solution. I removed the gromets with a plier and the injectors went in as supposed...
I am going to post some pictures for future reference tomorrow.
I am going to post some pictures for future reference tomorrow.
#15
Elite Member
Thread Starter
Join Date: Mar 2006
Location: Schwarzenberg, Germany
Posts: 1,557
Total Cats: 103
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Here are the pictures for future reference:
That is how the injectors came:
That is with the rubber gromets removed - you still need to wiggle them a bit around to make them sit properly.
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55585-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_10.jpg?dateline=1348465059)
In case somebody else has this problem...
That is how the injectors came:
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55584-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_09.jpg?dateline=1348465059)
That is with the rubber gromets removed - you still need to wiggle them a bit around to make them sit properly.
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/55585-new-id725cc-injectors-fuel-rail-not-sitting-flush-wtf-solved-id725_10.jpg?dateline=1348465059)
In case somebody else has this problem...