Girly Catch Can Mounted
#141
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Your log would show exactly what pressures you're dealing with, possibly producing evidence which would determine if OE vent size and baffles are adequate
#142
Junior Member
Join Date: Feb 2007
Location: 11368 miles from where i would like to be
Posts: 269
Total Cats: 92
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Indeed it would be feasible and not too hard. Just hook a map sensor to a spare ADC input and log the values. You can do the conversion to pressure afterwards easily. I'm interested to see what you find out, but you have to thrash the crap out of the car to do a good test on this.
#143
2 Props,3 Dildos,& 1 Cat
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
You fail reading comprehension.
If velocity stays the same pressure stays the same. Movement alone (without change on rate of movement etc) does not generate pressure differences.
Your equation is only valid away from any walls of say an intake tube and also only to incompressible fluids. The air in your intake satisfies neither of those requirements.
You are right that there will be a pressure gradient leading into the compressor, however its contour would be something like the inverse square. If you applied a still body of air to that vacuum source you might be able to detect it. With a steady state equilibrium reached where the speed of the air moving in and the pressure differential across it (it's invalid to say that it is sucked in just the same as it is invalid to say that it is pushed in) that makes it move are matched then the pressure drop relative to the outside ambient air should be so close to zero that you'd have a hard time measuring it. If it's not, your intake sucks.
End rant :-)
Fred.
If velocity stays the same pressure stays the same. Movement alone (without change on rate of movement etc) does not generate pressure differences.
Your equation is only valid away from any walls of say an intake tube and also only to incompressible fluids. The air in your intake satisfies neither of those requirements.
You are right that there will be a pressure gradient leading into the compressor, however its contour would be something like the inverse square. If you applied a still body of air to that vacuum source you might be able to detect it. With a steady state equilibrium reached where the speed of the air moving in and the pressure differential across it (it's invalid to say that it is sucked in just the same as it is invalid to say that it is pushed in) that makes it move are matched then the pressure drop relative to the outside ambient air should be so close to zero that you'd have a hard time measuring it. If it's not, your intake sucks.
End rant :-)
Fred.
and last time i checked, the ambient air outside my intake pipe is not moving and the air inside it IS moving.
I bet my intake tube flows better than any miata with a filter on this site.
![Biggthumpup](https://www.miataturbo.net/images/smilies/biggthumpup.gif)
#144
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I could get "moving" air between 10 psig and 11 psig, and have higher pressure. :-P
More to the heart of this conversation, you're not going to get *significantly* low pressure in the intake unless the system really is restrictive. A bad air cleaner might do a bit. Certainly an OEM intake has a significant pressure drop, though still not large.
Anyway, what I'm taking from all this is the OEM system is a good thing to shoot for, an upgraded PCV and catch can are what the descerning turbo enthusiast will be putting on his miata this season.
Mine are on order, and will be installed with catch can directly.
More to the heart of this conversation, you're not going to get *significantly* low pressure in the intake unless the system really is restrictive. A bad air cleaner might do a bit. Certainly an OEM intake has a significant pressure drop, though still not large.
Anyway, what I'm taking from all this is the OEM system is a good thing to shoot for, an upgraded PCV and catch can are what the descerning turbo enthusiast will be putting on his miata this season.
Mine are on order, and will be installed with catch can directly.
#147
Junior Member
Join Date: Feb 2007
Location: 11368 miles from where i would like to be
Posts: 269
Total Cats: 92
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Not only is your filter half the size of mine (flow area wise) your intake tube is also less than half at the intake end! ;-) (It's the same at the turbo though) Mine also has a "velocity stack" leading from the 6" into the 4" <<< (quotes required for Dr Evil style pronunciation)
I'm sorry for being less of a man than you y8s ;-) I'll just have to take consolation in the fact that I'm less of a man while not driving a Miata :-)
Fred. (living dangerously)
I'm sorry for being less of a man than you y8s ;-) I'll just have to take consolation in the fact that I'm less of a man while not driving a Miata :-)
Fred. (living dangerously)
#149
2 Props,3 Dildos,& 1 Cat
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Not only is your filter half the size of mine (flow area wise) your intake tube is also less than half at the intake end! ;-) (It's the same at the turbo though) Mine also has a "velocity stack" leading from the 6" into the 4" <<< (quotes required for Dr Evil style pronunciation)
I'm sorry for being less of a man than you y8s ;-) I'll just have to take consolation in the fact that I'm less of a man while not driving a Miata :-)
Fred. (living dangerously)
I'm sorry for being less of a man than you y8s ;-) I'll just have to take consolation in the fact that I'm less of a man while not driving a Miata :-)
Fred. (living dangerously)
honestly, with a filter on there mucking it all up, it probably is sub optimal anyway.
#151
Junior Member
Join Date: Feb 2007
Location: 11368 miles from where i would like to be
Posts: 269
Total Cats: 92
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
my velocity stack is built into the turbo. if I ran a different compressor housing, i'd be all over a velocity stack, but I'd probably put it in front of a filter to avoid obstructing the opening of the stack.
honestly, with a filter on there mucking it all up, it probably is sub optimal anyway.
honestly, with a filter on there mucking it all up, it probably is sub optimal anyway.
All bullshit aside, a lot of the stuff we all do to our cars make so little difference that it just doesn't matter. Even when you assemble them all together the increase in HP isn't that much. The key thing is to not do anything badly :-)
I'm going to summarise all of Rob's PCV threads into an article at some point when I have more time. I'll link it here when I do.
Fred.
#154
Junior Member
Join Date: Feb 2007
Location: 11368 miles from where i would like to be
Posts: 269
Total Cats: 92
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
www.autoshop101.com/forms/h63.pdf
Toyota and Braineack seem to disagree on PCV valve operation. I'm with Toyota on this and claim you shouldn't/don't need the check valve. I'll stick with that opinion until someone proves that their crank case is being pressurised by boost through a pcv sized hole when the exit hole is equally sized or larger. (note, not physically possible :-p)
You do the loveliest diagrams Rob! I'd note that the "breather" location needs to flow well and that the main issue seems to be that it doesn't and the crank case get's pressurised.
Fred.
Toyota and Braineack seem to disagree on PCV valve operation. I'm with Toyota on this and claim you shouldn't/don't need the check valve. I'll stick with that opinion until someone proves that their crank case is being pressurised by boost through a pcv sized hole when the exit hole is equally sized or larger. (note, not physically possible :-p)
You do the loveliest diagrams Rob! I'd note that the "breather" location needs to flow well and that the main issue seems to be that it doesn't and the crank case get's pressurised.
Fred.
#155
Elite Member
Thread Starter
iTrader: (5)
Join Date: Jan 2005
Location: Atlanta
Posts: 7,486
Total Cats: 372
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
And here's a diagram for a cheap catch can. This fixes some stuff wrong with mine. I don't have the pipe nipples penetrating into the can nor the divider, so some of the oil vapor actually makes it out of the filter I have stuck on the end (no it doesn't go to the turbo intake...yet). So that means if it did run to the intake, I'd have vapor condensing in the hose and possibly making it to the compressor. The divider wall and pipe nipples should for the vapor deeper into the can and provide more surfaces/opportunity for condensation. I prefer the divider over packing.
![](http://i158.photobucket.com/albums/t86/m2cupcar/current%20FEmx5t/pvccatchcan.jpg)
#157
Junior Member
Join Date: Feb 2007
Location: 11368 miles from where i would like to be
Posts: 269
Total Cats: 92
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
No discovery required. The throttle plates in stock config pass almost no air at all. The PWM idle control corrects idle level based on what the rpm actually is. Thus, if it's getting some air from the crank case it's going to close the PWM valve to match. Likewise, if it's getting some O2 free gas from there it's going to feed in sufficient air to keep the idle up. Given the diameter of the PCV orifices and the engines idle air requirement, I doubt you could keep it alive based only on the PCV "leak".
#158
Junior Member
Join Date: Feb 2007
Location: 11368 miles from where i would like to be
Posts: 269
Total Cats: 92
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Too slow with the edit there... or too fast.
Yes really. You stated that it is CLOSED at high vacuum. It is not closed, merely restricted. Restriced != Closed.
Smile, it'll do ya good :-)
Yes really. You stated that it is CLOSED at high vacuum. It is not closed, merely restricted. Restriced != Closed.
Smile, it'll do ya good :-)
#160
Elite Member
Thread Starter
iTrader: (5)
Join Date: Jan 2005
Location: Atlanta
Posts: 7,486
Total Cats: 372
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I'd be curious to know the exact differences between the stock miata valve and the gtx, and why the stock unit is built the same. What compromise is made with the gtx valve being more resistant to boost?