Nice work Braineack.

Oooohhhhh that looks nice. Guess I'll be doing mine with some insulated heat shrink bullet connectors.

What's your plan Y8s?

Looks tizzzight!

i'm getting some pins from brainboy to put in my toyota connector housings and i've got 37 million feet of various loom sizes or a trip to www.wirecare.com (omg stainless zip ties!) and probably something similar to what scott did. then run the four back to the proper hydra pins. i may need to get more crimp pins from FM though.

Speaking of crimp pins.
I am fixing the mess that the prevous owner made of my stock ECU harness. In the process one of the wires fell apart right at the crimp pin and I don't know how to get the pin out. I was under the impression that you just insert something into the little hole and pull the pin out. I used a needle because it was the only thing small enough to slide in the hole and I still can't get the pin out. I think i need a paper clip hammered flat or something because nothing else is small enough to get in that little slot.

I am still waiting on 2 COPs from lazzer, i did get connectors out of the deal but it sucks being short 2 coils.

if i recall, the NB connectors have a "latch" in them. let me see...

http://ecommas.tycoelectronics.com/c...1-5763-1_A.pdf

page 7-9, figures 11-13.

Matt

Mine look a bit different than those, though maybe all i need is a stronger more flat tool that I can pry up with. I'll try it in the daylight. If it doesn't work i'm soldering directly to the outside of the pin and closing the door latch on the back. It's just the idle wire anyway.

Braineack,
So are you gonna throw together a few harnesses for locals? I'll throw some bucks your way. Make mine exactly like Y8s. I got an NB. :) Don't need a tach signal if my reading is right.

Frank

Braineack,
I'm interested in getting the connectors. I just picked up my last to coils yesterday and I'm getting ready to make the harness. Are you selling the just the pigtails or a whole pnp harness? I can probably get like 5 ignitors for the NA's if you need them.

Talk to Ben, im not making these harnesses. Busy building Megasquirts.

Braineak,
Are those the same connectors that 'y8s' is using, Toyota part number : 90980-11885. If so can I get 16 of the pins and I'll order the connectors from the website he listed and I can make my own harness. Thanks

Just to gloat... I got connectors! :p

Braineak - I'll take a set of pins
 

Braineak - I'll take a set of 16 pins. Can Paypal, let me know here: wallyman (at) miatamonkey (dot) com. Thanks!!!

Connectors
 

x2

Is 90980-11885 the connector in those kick-azz photos??

Wallyman

yeah I'm makin' my own. And before you ask--it's way low on the project list ;)

Man. you guys can't click back a few pages? This fits the coils. pins separate. Braineack needs to post the p/n and then you can all buy them at onlinecomponents.com and distribute them amongst yourselves because they have like a $30 minimum which adds up to fifty jillion pins.

Since my car is running OK, this is really low on my project list behind epoxying my garage floor this weekend, putting in a 4-post lift, installing a sprinkler system, and re-tiling the bathroom. At least the COPs look good sitting on my work bench.

Frank

Funny how your list and mine are so similar. Except the lift installation. I go use one of my dad's. :)

i did.


time to create a page for the archives. :bang:

partznet.com was $1.75 cheaper (shipping) than discounttoyotaparts.com despite them appearing to be the same website (or at least ordering engine).

I couldn't find a valid 10% off coupon code. All were expired.

Braineack,
Do you still have 16 pins available? Can I paypal you some bucks for them.

Frank