SOL yes I did.
Everyone else I'm using your Paypal addresses right? |
Yes.
|
sure
|
Originally Posted by lazzer408
(Post 139734)
To some extent. The rubber seal does contact the valve cover but is not molded to fit as well as it might fit the 1ZZFE.
|
Originally Posted by Joe Perez
(Post 140528)
I must have gotten a different coilset. On mine, there's about 3/8" space betwixt coil and valve cover when fully seated. On a 1.6 engine.
|
biggest DIY thread ever
|
Originally Posted by lazzer408
(Post 140427)
SOL yes I did.
Everyone else I'm using your Paypal addresses right? |
it said in my paypal to use my paypal address. "yes"
|
Joining this discussion. Great idea here. I tried the Chrysler/AEM TwinFire amplifier COP system once. Worked okay until the AEM box fried itself. Took it off and run OEM coils again. This COP idea seems to be much less maintenance and in keeping with the KISS theory.
Only thing is I don't want to cut into the factory ignition harness again after the last debacle. I noticed an image of a connector on a previous page. That looks like it may fit the OEM coil connectors going to the 1.8l coils on my engine. I'd really like to find a connector that I could PnP with so I don't have to cut the 1.8l ignition harness again. I already bought a set of 1ZZ coils off ebay. Just want to find a connector for the OEM ignition coil connectors before jumping on this project. |
Just finished my PnP harness for mine. Still wish I had the toyta cop connectors... but i made do.
http://www.imagestation.com/picture/...e/e81823f7.jpg http://www.imagestation.com/picture/...7/e81823ef.jpg http://www.imagestation.com/picture/...d/e81823e4.jpg I'll test it all out, once I figure how I want to mount it. |
Looks good. To bad I can't just disassemble an ignitor to do that for my '99.
|
Hey-what a good idea :D
|
hey-I mentioned it weeks ago...
Looks good Splitime. You welding on stand-offs now? |
Originally Posted by Splitime
(Post 141018)
Just finished my PnP harness for mine.
http://www.imagestation.com/picture/...d/e81823e4.jpg I'll test it all out, once I figure how I want to mount it. |
It looks like a gutted ignitor with the wires coing out of teh back from a hole.
Looks like it will be neat. Congrats.:bigtu: |
Originally Posted by Splitime
(Post 141018)
Just finished my PnP harness for mine. Still wish I had the toyta cop connectors... but i made do.
... I'll test it all out, once I figure how I want to mount it. Incredibly clean - very nice job! Jeff |
Now if only it worked 100% :p. I got car up on them first try, idle smooth, didn't test beyond that.
But... no tach. I have all 4 tach outputs merging and then merged with the 2 center wires on the ignitor.... I"m so close. |
Originally Posted by lazzer408
(Post 141035)
hey-I mentioned it weeks ago...
Looks good Splitime. You welding on stand-offs now? |
Will the plugs not just sit on the spark plugs? Or do they not clip onto the plug like most plug wires do?
|
no they'll come off when you're driving. they fit on the plugs, but not as snugly as plug wires do.
dave, I find your tach issue odd. I'm planning on isolating all the tach outs from each other with diodes. perhaps that's an issue. |
All times are GMT -4. The time now is 08:14 AM. |
© 2024 MH Sub I, LLC dba Internet Brands