Boost Overshoot
#1
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I have a home-depot MBC, with a tiny bleeder hole drilled in the side. It's hooked up to reference just before the TB.
I get boost overshoot. I would like to be running between 12 and 13psi, but if I set it up to do that it will overshoot to 15 or 16, hitting the overboost fuel cut. I have it set up now to overshoot to about 13 and settle around 10, but I'm looking for ideas on how to get rid of the overshoot completely.
It's an internal wastegate and the actuator limits boost to about 7.5psi when left to it's own devices. I attached a log of the problem.
I get boost overshoot. I would like to be running between 12 and 13psi, but if I set it up to do that it will overshoot to 15 or 16, hitting the overboost fuel cut. I have it set up now to overshoot to about 13 and settle around 10, but I'm looking for ideas on how to get rid of the overshoot completely.
It's an internal wastegate and the actuator limits boost to about 7.5psi when left to it's own devices. I attached a log of the problem.
#2
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
it's possible sourcing boost after the IC would help with the spike.
You could probably use a helper spring to help keep the wastegate closed with more rpms. what's happening now is, it's not opening enough then it's staying open too far.
You could probably use a helper spring to help keep the wastegate closed with more rpms. what's happening now is, it's not opening enough then it's staying open too far.
#3
Tour de Franzia
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I agree with brain, and just get a stronger wastegate, closer to your target boost. I tried running my "14psi spring" with no vac hose and wired closed...no change in spoolage.
Do you have a gt2860rs? The only way I could get mine to stop overboosting was raise target to 14.7psi. In the cold it overboosts to 17 or 18, but I straight don't give a **** because I'm baller and bitches love me. Goose bottles left and right, bro.
Do you have a gt2860rs? The only way I could get mine to stop overboosting was raise target to 14.7psi. In the cold it overboosts to 17 or 18, but I straight don't give a **** because I'm baller and bitches love me. Goose bottles left and right, bro.
#6
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I tried the helper spring with no luck. I couldn't find anything on here about the helper spring but the subaru forums have some stuff on it so I bought a spring and put it on, and stretched it pretty tight but I still get the exact same result. How strong does this spring need to be?
#9
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
if I wire the gate shut, it will just make more boost than I want to put into the engine. I have problems keeping the overshoot under the fuel cut as it is, with the gate wired shut the boost will climb until at least 18psi.
#10
Supporting Vendor
![](/mt2011/images_td/ranks/vendor.png)
iTrader: (3)
Join Date: Jul 2006
Location: San Diego
Posts: 3,303
Total Cats: 1,216
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Helper springs, a different wastegate, etc. are all bandaids that don't address the real problem and won't help. Don't spend any more $ trying to fix this issue when you can set it up right for under $10 - you are not really having 'overshoot' - you are having drop off. As in, when your MBC is set for 15-16 psi and you are dropping off to 12-13 by redline because of pressure drop across the intercooler.
Read my thread here: https://www.miataturbo.net/forum/t32479/
Go do this and you will be able to set your MBC to 13 psi and you should drop at most to 12 psi at redline.
-Ryan
Read my thread here: https://www.miataturbo.net/forum/t32479/
Go do this and you will be able to set your MBC to 13 psi and you should drop at most to 12 psi at redline.
-Ryan
#11
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Read my thread here: https://www.miataturbo.net/forum/t32479/
Go do this and you will be able to set your MBC to 13 psi and you should drop at most to 12 psi at redline.
-Ryan
Go do this and you will be able to set your MBC to 13 psi and you should drop at most to 12 psi at redline.
-Ryan
FWIW, it does act more like boost drop than overshoot sometimes, but othertimes it acts more like overshoot than boost drop. It's a weird problem.
#12
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My reference was to the helper spring. Tying the wg shut will show you what you're spools like w/o the boost overpowering your internal gate and blowing by the valve on spool. If it spools better with the gate wired shut then you know it's leaking during spool up. Then a helper spring will help on spool up- even though it's a bandaid, it works and it's why they're used on gates that have a weak spring. Mine reduced spool up by something like 600rpm and with that I managed to nail target and hold boost to redline with only a .8psi variation from target.
Regarding your current problem- as mentioned above, moving your reference signal to the IC pipe right before the tb can help reduce (or even remove) the spike you're seeing.
Regarding your current problem- as mentioned above, moving your reference signal to the IC pipe right before the tb can help reduce (or even remove) the spike you're seeing.
#14
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
There's a thread somewhere on here that discusses the spring strength. The second part is adjusting the tension on the spring with a thread rod. Once you know what the turbo spools at with the wastegate tied shut, then you aim for the same using your spring adjustment until you overshoot the mbc target, then go back to the previous setting.
#15
Supporting Vendor
![](/mt2011/images_td/ranks/vendor.png)
iTrader: (3)
Join Date: Jul 2006
Location: San Diego
Posts: 3,303
Total Cats: 1,216
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Back when I was fussing around with helper springs I found a variety pack of different strengths at Home Depot. Use a threaded eye-bolt to attach it to the wastegate actuator's bracket and then you can adjust the tension of the spring properly. Then just adjust, test, adjust again until you find the sweet spot.
#16
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I'm still not entirely sure what I'm adjusting to. I got a much stronger spring and a threaded eye bolt to play with, but am I really just trying to match wired-closed spool to fix my overshoot/drop problem?
#18
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I am beginning to get very frustrated with this. I have tried everything that has been suggested and none of it seems to make any difference. I've got a giant spring on the WG and I loosened the MBC way up and it still overshoots. If I tighten the spring, it just does the same thing, 3psi higher.
Hustler, I tried covering the hole in my valve and it doesn't seem to make any difference either.
Hustler, I tried covering the hole in my valve and it doesn't seem to make any difference either.
#20
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My downpipe is a custom 2.5" piece, and the exhaust is 2.5 straight through with a "high-flow" cat.