AEM Datastream Gauge
#1
Junior Member
Thread Starter
iTrader: (5)
Join Date: Jun 2007
Location: Jacksonville, FL
Posts: 182
Total Cats: 0
AEM Datastream Gauge
I'm looking into gauges and I've found the AEM Serial Datastream gauge to be very appealing. Does anyone know if you still need the Uego controller with it or if this is all you need? I noticed it includes the Bosch sensor so I was unsure. Also, what are your opinions on it? Worth the money or is it a better bet to just get regular mechanical gauges?
Link to AEM site, http://aempower.com/ViewCategory.aspx?CategoryID=64.
Link to one on ebay, http://cgi.ebay.com/ebaymotors/AEM-G...spagenameZWDVW.
Link to AEM site, http://aempower.com/ViewCategory.aspx?CategoryID=64.
Link to one on ebay, http://cgi.ebay.com/ebaymotors/AEM-G...spagenameZWDVW.
#7
Junior Member
Thread Starter
iTrader: (5)
Join Date: Jun 2007
Location: Jacksonville, FL
Posts: 182
Total Cats: 0
Yea that's what I was thinking. The only thing I don't like is that I can't watch every channel at once, so unless something is really going out of the min/max range I won't be able to tell. Plus I'll have to figure out the AEM software to change the values, etc.
#9
Elite Member
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
I'm looking into gauges and I've found the AEM Serial Datastream gauge to be very appealing. Does anyone know if you still need the Uego controller with it or if this is all you need? I noticed it includes the Bosch sensor so I was unsure. Also, what are your opinions on it? Worth the money or is it a better bet to just get regular mechanical gauges?
Link to AEM site, http://aempower.com/ViewCategory.aspx?CategoryID=64.
Link to one on ebay, http://cgi.ebay.com/ebaymotors/AEM-G...spagenameZWDVW.
Link to AEM site, http://aempower.com/ViewCategory.aspx?CategoryID=64.
Link to one on ebay, http://cgi.ebay.com/ebaymotors/AEM-G...spagenameZWDVW.
If you have the AEM EMS, this is all you need to view a few parameters. I have this gauge, and am disappointed in the difficulty using it. I don't feel like explaining much, but it does not work as advertized. The only things that work/display as they should are coolant temp, air temp, O2, vehicle speed, and TPS. There is no easy way to display knock voltage, engine load (boost), rpm, etc. Engine load is displayed as a percentage of load, and it's difficult to determine or set what "100%" even is. I'd want it to display boost pressure, but haven't figured that out.
EDIT: Everything is explained better here, I am just too lazy to figure out and configure the gauge software. You should be able to display any parameter within AEMPro software.
http://forum.aempower.com/forum/inde...c,14826.0.html
Last edited by TurboTim; 08-16-2007 at 10:20 AM.
#12
Junior Member
Thread Starter
iTrader: (5)
Join Date: Jun 2007
Location: Jacksonville, FL
Posts: 182
Total Cats: 0
Hey sorry to dredge this post back up but I'm ready to buy my wideband and datastream gauge, but my post count is still too low to PM. Could you guys email or PM me the prices for both gauges shipped to 32210? Thanks.
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM