ABSURDflow Turbo KLDE Mazda V6 Thread
#422
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Yeah that's what I'm hoping, something like that. I have the ~7psi spring combo in my EWG and if it doesn't feel as fast or faster than the old setup I'll be sad.
I'm going to dump the EWG instead of plumbing it back into the downpipe. Life's too short to do extra fab work.
I'm going to dump the EWG instead of plumbing it back into the downpipe. Life's too short to do extra fab work.
#425
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I have never touched a megasquirt or it's tuning software. One day I will may have an application for one. Maybe a microsquirt on my seadoo.
I'd try Braineack or reverant or diyautotune?
I'd try Braineack or reverant or diyautotune?
#429
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I finally got around to finishing the intercooler and EWG dump pipe, so no reason to not install the turbo.
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65610-absurdflow-turbo-klde-mazda-v6-thread-ewgdump1.jpg?dateline=1359169737)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65611-absurdflow-turbo-klde-mazda-v6-thread-012513.jpg?dateline=1359169737)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65612-absurdflow-turbo-klde-mazda-v6-thread-ewgdump3.jpg?dateline=1359169737)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65613-absurdflow-turbo-klde-mazda-v6-thread-ewgdump4.jpg?dateline=1359169737)
I just need to drain the break-in oil and pick up some hose fittings for the boost control solenoid. I'll probably start it tomorrow, but it's snowing at the moment so a test drive will have to wait.
I hope to have the new intake manifold done by summer.
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65610-absurdflow-turbo-klde-mazda-v6-thread-ewgdump1.jpg?dateline=1359169737)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65611-absurdflow-turbo-klde-mazda-v6-thread-012513.jpg?dateline=1359169737)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65612-absurdflow-turbo-klde-mazda-v6-thread-ewgdump3.jpg?dateline=1359169737)
![](https://www.miataturbo.net/attachments/diy-turbo-discussion-14/65613-absurdflow-turbo-klde-mazda-v6-thread-ewgdump4.jpg?dateline=1359169737)
I just need to drain the break-in oil and pick up some hose fittings for the boost control solenoid. I'll probably start it tomorrow, but it's snowing at the moment so a test drive will have to wait.
I hope to have the new intake manifold done by summer.
#431
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Thanks! I guess & check mostly. If you guess wrong, you cut off XX angle. Eventually you have enough cutoffs in the scrap bin that you can piece together the bends using the smaller cutoffs before you use the new/good pipe.
In 2.5 & 3" diameters I have a good assortment of angle pieces that I tack together in whatever combo I need to try a bend angle.
With that 1.75" EWG dump, I was lucky. It's a 90, to a 45, to two 22.5's. I used one complete vibrant tight radius U bend. I need another inch or so to make it below the undertray though
In 2.5 & 3" diameters I have a good assortment of angle pieces that I tack together in whatever combo I need to try a bend angle.
With that 1.75" EWG dump, I was lucky. It's a 90, to a 45, to two 22.5's. I used one complete vibrant tight radius U bend. I need another inch or so to make it below the undertray though
![vash](https://www.miataturbo.net/images/smilies/vash.gif)
#433
Supporting Vendor
![](/mt2011/images_td/ranks/vendor.png)
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (1)
Join Date: Sep 2010
Location: Lake Forest, CA
Posts: 7,976
Total Cats: 1,019
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
This has got to be one of the coolest, most well-done builds I've ever seen. And I can only imagine what it's going to sound like. I will see this car in action, in person, someday. Hearing that KLiata that was for sale a while back was just awesome.
Props props.
Props props.
#440
Elite Member
iTrader: (13)
Join Date: Dec 2006
Location: Taos, New mexico
Posts: 6,763
Total Cats: 631
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
****. This is beyond sick, i can only imagine the torque curve that thing makes.
Proper miata right here.
Any chance you did a 3rd/4th gear datalog so we can see the virtual dyno results? Looks like an easy 300whp and tons of torque.
Proper miata right here.
Any chance you did a 3rd/4th gear datalog so we can see the virtual dyno results? Looks like an easy 300whp and tons of torque.