Absurdflow Low Mount (A/C P/S friendly)
#81
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I hope to God I never have to touch this car again. A/C & P/S wasn't so bad, but dealing with the windshield washer in the fender (because of the ABS) and the cruise control actuator was a pain in the ****. I made one pipe and the cruise gizmo bracket twice because I originally hoped to keep the OEM MAF out of the plumbing. The never ending car project (not even done when he arrived!!). I can go off on this thing for a half hour but I have to get back to work.
After I got it from Paul post-tuned, I only drove it to fill it up with gas, but it was very fun
After I got it from Paul post-tuned, I only drove it to fill it up with gas, but it was very fun
![](https://www.miataturbo.net/images/smilies/smile.gif)
#88
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
It's nothing personal against you, don't think that! You were great and very patient, and you paid which is always good.
#89
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I got 10 flanges from him just last week, thanks! I have enough flanges not to last a life time...I think it's time to try to sell some for a loss, cause they are no good to me collecting dust.
#92
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (9)
Join Date: Jun 2006
Location: Chesterfield, NJ
Posts: 6,922
Total Cats: 402
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I finally had some free time to upload some pics I took once the car was back at my place to do the final little bits after Paul did the megasquirt install/tune. Here's what a few weeks at "the shore" will do to a mild steel manifold that sits around.
Before:
![](http://www.absurdflow.com/miata/acpst2/jpeg/acpst2build10%20copy.jpg)
After:
![](http://www.absurdflow.com/miata/acpst2/jpeg/acpst2build23%20copy.jpg)
Lots of room!![Bang](https://www.miataturbo.net/images/smilies/bang.gif)
![](http://www.absurdflow.com/miata/acpst2/acpst2build22.jpg)
More pics here:
Ed's A/C & P/S ABSURDflow low mount setup
Before:
![](http://www.absurdflow.com/miata/acpst2/jpeg/acpst2build10%20copy.jpg)
After:
![](http://www.absurdflow.com/miata/acpst2/jpeg/acpst2build23%20copy.jpg)
Lots of room!
![Bang](https://www.miataturbo.net/images/smilies/bang.gif)
![](http://www.absurdflow.com/miata/acpst2/acpst2build22.jpg)
More pics here:
Ed's A/C & P/S ABSURDflow low mount setup