1996 Mazda Miata - $7000
#1
Thread Starter
Junior Member
iTrader: (4)
Joined: Mar 2008
Posts: 47
Total Cats: 0
From: Santa Monica
1996 Mazda Miata - $7000
Category: Import
Status: Clean Title
I have a 1996 Mazda Miata for sale, in USA - California.
Mileage: 93000 miles
VIN: JM1NA3532T0713767
Engine Size: 1.8
Asking price is $7000
1996 Miata M-edition JRSC, less than 93k, bought with 87k in 2008 so all mods/maintenance are about 2 years old.
PRICE: $7000 obo
PICS: http://cid-10f5145ea28cfdd6.skydrive...4hfzOo0p!Ss%24
Was planning on swapping from supercharged to turbo, but now that I have a new kid, the miata (my old kid) has to go. At this point I will not part out, and I will include all the uninstalled parts.
Basically there is nothing wrong with the car, all the maintenance has been done. Body has a few dings and scrapes, but paint still shines. This is an east coast car, so there is one rust spot (in pics).
I installed the MSPNP last month, and didn't tune it much, since I didn't install the wideband yet. It's been driven about 20 miles since the MSPNP install.
$7000 obo
ICE
KENWOOD KAC-X4R eXcelon 4-CH AMP 1200W AMPLIFIER
2 x 9Kv.2 Subwoofer (9Kv.2)
CDT-620 system with satnet-480 crossovers 8
KENWOOD KDC-X890 EXCELON CD/MP3/USB
TSUNAMI AMP48-CAP 4 GA GAUGE (2) AMP KIT WITH CAPACITOR 8
INTERIOR
Upper and lower shift boot
Redline goods – Miata 90-05 both boots & armrest cover, Black leather, Tan thread
Black Visor Plate Pair
2 (MM035-TN) Tan Vinyl In-Between Pocket
1 (MM050) Black Expandable Cup Holder
Floor Mats – Medition
M1 Interior Dress Up Package
Recover Seats and foamectemy
EXTERIOR
Licesne plate swing kit
Rattle can black M wheels with Ziex tires - 70% tread left
Blinking third brake light
Turn signal Intake
Fenders Rolled
ICHIBA V2 20mm Spacers
ENGINE
JRSC with DDM CAI
MS PNP $550
Extra MS parts – 1 x 3/8” NPT Stainless Steel Weld-On Bung for IAT or CLT Sensor (38NPT-BungSS)
1 x USB to Serial Adapter
TDR Belt Tensioner with steel pulleys
NGK V-Power Spark Plugs (Box of 4 plugs),NGK-BKR6E-11
TDR SC Nose Pulley,: TDR-PULY4-62
Supercharger Bypass Check Valve , Item #:TDR-CHK-VAL
Wire Spark Plug Wires: TDR-LW90-RED
ACTUATOR, BYPASS
1 x Exedy Stage 1 Organic Clutch Kit
3 x MotorCraft "Full Synthetic Manual transmission fluid - XT-M5-QS
1 x Redline 75w90NS
MAZDA MIATA Radiator 7 KOYO (170425215355)
Coolant Hose Kit 1994-1997
Cobalt Cat-Back Performance Exhaust System
SUSPENSION / BRAKES
FM Stage 1 – Illumina/FM Springs
Motor mounts
Differential Bushings
FM – Butterfly Brace
reman Front Calipers
Reman Rear Calipers
Stainless brake lines and clutch line
Brembo Rotors – Front and Rear
Akebono Pads – Front and Rear
Energy Suspension Base kit
Energy Suspension Boots (2 sets)
NOT INSTALLED
460cc injectors
Deatschwerks Cleaning
Innovate Motorsports G3 Gauge Kit (G3 Gauge, LC-1 & O2 Sensor)
1 x Innovate Motorsports G3 Vacuum / Boost Gauge
R-Speed front and rear lips
Bipes ACU
Standard Supercharger Rebuild Kit
#5
Thread Starter
Junior Member
iTrader: (4)
Joined: Mar 2008
Posts: 47
Total Cats: 0
From: Santa Monica
If someone was interested, I could remove the following parts from the package to make the deal $4500. So for $4500, you would not get the following parts:
460cc injectors cleaned by Deatschwerks
Innovate Motorsports G3 Gauge Kit (G3 Gauge, LC-1 & O2 Sensor)
Innovate Motorsports G3 Vacuum / Boost Gauge
R-Speed front and rear lips
Bipes ACU
CDT-620 system with satnet-480 crossovers 8 (might replace with pioneer seperates)
Standard Supercharger Rebuild Kit
Turn signal Intake (would replace with stock front lights)
ICHIBA V2 20mm Spacers
MS PNP (would replace with stock ECU + powercard + 02 clamp)
Extra MS parts – 1 x 3/8” NPT Stainless Steel Weld-On Bung for IAT or CLT Sensor (38NPT-BungSS), 1 x USB to Serial Adapter
This car would make a great daily, or sell the supercharger and go turbo (which is what I wanted to do).
460cc injectors cleaned by Deatschwerks
Innovate Motorsports G3 Gauge Kit (G3 Gauge, LC-1 & O2 Sensor)
Innovate Motorsports G3 Vacuum / Boost Gauge
R-Speed front and rear lips
Bipes ACU
CDT-620 system with satnet-480 crossovers 8 (might replace with pioneer seperates)
Standard Supercharger Rebuild Kit
Turn signal Intake (would replace with stock front lights)
ICHIBA V2 20mm Spacers
MS PNP (would replace with stock ECU + powercard + 02 clamp)
Extra MS parts – 1 x 3/8” NPT Stainless Steel Weld-On Bung for IAT or CLT Sensor (38NPT-BungSS), 1 x USB to Serial Adapter
This car would make a great daily, or sell the supercharger and go turbo (which is what I wanted to do).
Last edited by webninja; 06-17-2010 at 07:20 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 09:17 PM