Shuiend blows motor #5; Naturally Aspirated Glory Incoming
#61
I may remember poorly, but I imagine this isn't an issue since you were running the car on MS3 prior.
This makes me sad.
From the above advice I'd keep running compression checks, hitting the bleed button after every two cycles, and seeing if you ever get a cycle where it doesn't compress. If so then look at your intake cam again.
#62
Senior Member
iTrader: (14)
Join Date: Aug 2008
Location: Tinley Park, IL
Posts: 1,482
Total Cats: 0
Might be worth a try if it's an easy swap.
#64
Senior Member
iTrader: (14)
Join Date: Aug 2008
Location: Tinley Park, IL
Posts: 1,482
Total Cats: 0
Man it sure sound like the timing is off. Is it hissing like it's blowing the compression out an open valve or am I hearing things?
Either way, it still doesn't explain why it's cranking so slow. What did you guys use for assembly lube? What bearing clearance are you running?
Either way, it still doesn't explain why it's cranking so slow. What did you guys use for assembly lube? What bearing clearance are you running?
#66
Senior Member
iTrader: (14)
Join Date: Aug 2008
Location: Tinley Park, IL
Posts: 1,482
Total Cats: 0
It kinda does, yeah. At the beginning of the vid it sounds like it's trying to compress but not firing at the right time. During the rest of the vid, though, it frespins like it's not compressing at all. It sounds like cam timing is off and it's blowing compression through an open valve and echoing in the manifolds.
Wierd.
Shuiend, did you guys verify it was definately at TDC when the cam timing was set? Is it a known good balancer with no chance of a slipped timing mark?
Wierd.
Shuiend, did you guys verify it was definately at TDC when the cam timing was set? Is it a known good balancer with no chance of a slipped timing mark?
#67
mkturbo.com
Thread Starter
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,189
Total Cats: 1,685
The strange noise on the second half of the video is from the throttle being pushed down for flood clear. We did not want to flood the engine.
Yes we verified that the crank was at TDC when we did timing. We put a dipstick in cylinder 1 and made sure it was at the highest point then.
After trying to crank the car all day we also manually turned it tell the crank was at TDC and timing marks on the cam gears still lined up perfectly.
Yes we verified that the crank was at TDC when we did timing. We put a dipstick in cylinder 1 and made sure it was at the highest point then.
After trying to crank the car all day we also manually turned it tell the crank was at TDC and timing marks on the cam gears still lined up perfectly.
#70
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
So here's the weird part about shuiend's setup:
We whipped out the timing light, set the timing in tunerstudio to a fixed 10 degrees BTDC and futz with the trigger offset until #1 cylinder plug wire makes the light flash at the right place.
we unclip the thing and go about trying to crank it a few times and then after a few minutes re-check the timing with the timing light. It'll be out 90 degrees one way or the other from where it was.
All timing / rotation information is coming from a stock 1994 CAS and looks normal on the tooth logger screen. Here's is a Joe Perez posted picture that shows about what Lars' looks like:
(ganked from this thread: https://www.miataturbo.net/megasquirt-18/sanity-check-inverted-primary-trigger-required-jimstim-29726/ )
so unless there's a rising/falling edge problem where it gets correct sync about 50% of the time and incorrect sync about 50% of the time, I am not sure what is going on.
We whipped out the timing light, set the timing in tunerstudio to a fixed 10 degrees BTDC and futz with the trigger offset until #1 cylinder plug wire makes the light flash at the right place.
we unclip the thing and go about trying to crank it a few times and then after a few minutes re-check the timing with the timing light. It'll be out 90 degrees one way or the other from where it was.
All timing / rotation information is coming from a stock 1994 CAS and looks normal on the tooth logger screen. Here's is a Joe Perez posted picture that shows about what Lars' looks like:
(ganked from this thread: https://www.miataturbo.net/megasquirt-18/sanity-check-inverted-primary-trigger-required-jimstim-29726/ )
so unless there's a rising/falling edge problem where it gets correct sync about 50% of the time and incorrect sync about 50% of the time, I am not sure what is going on.
#72
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
he has a spare CAS. nothing should have failed from when he pulled the motor the day before until we put the new one in the next day. it was running perfectly fine on the stock motor, nothing changed but the motor.
#76
I'm going to assume that what I'm about to mention has absolutely nothing to do with the problem, but I just wanted to mention it as a random, albeit extremely remote, possibility.
Is the exhaust clogged up? old mouse nest? Potato? Water? Disconnect/ unbolt the DP from the cat, and try it out.
*Oh no ****!? 500 posts! LOL*
Is the exhaust clogged up? old mouse nest? Potato? Water? Disconnect/ unbolt the DP from the cat, and try it out.
*Oh no ****!? 500 posts! LOL*
#77
mkturbo.com
Thread Starter
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,189
Total Cats: 1,685
I'm going to assume that what I'm about to mention has absolutely nothing to do with the problem, but I just wanted to mention it as a random, albeit extremely remote, possibility.
Is the exhaust clogged up? old mouse nest? Potato? Water? Disconnect/ unbolt the DP from the cat, and try it out.
*Oh no ****!? 500 posts! LOL*
Is the exhaust clogged up? old mouse nest? Potato? Water? Disconnect/ unbolt the DP from the cat, and try it out.
*Oh no ****!? 500 posts! LOL*
#78
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,360
Total Cats: 1,184
I don't want to discount your diagnostic skills or the fact that your car ran great on the previous motor, but you've been assuming A LOT since the beginning of these problems. All of which have to do with things you didn't touch. Don't forget to take a look at those, **** happens.
#79
Elite Member
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
I don't want to discount your diagnostic skills or the fact that your car ran great on the previous motor, but you've been assuming A LOT since the beginning of these problems. All of which have to do with things you didn't touch. Don't forget to take a look at those, **** happens.
#80
mkturbo.com
Thread Starter
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,189
Total Cats: 1,685
I will say,
I did assume that I had put on my cam caps correctly, this is the first VVT head I have ever messed with and the cam caps do not have arrows on them pointing which way to go like the earlier heads. So I put them on what made the most sense based on how I had the head oriented on the table when I assembled it.
I did assume that I had the timing correct when I did it with the motor outside of the car. Yet again I have never done timing on a VVT motor and the intake cam definitely is not as user friendly as the other intake cams on earlier heads. Although at most the timing was only off a tooth or so on either side so it should still start, probably would not run great, but start none the less.
I did assume that I had put on my cam caps correctly, this is the first VVT head I have ever messed with and the cam caps do not have arrows on them pointing which way to go like the earlier heads. So I put them on what made the most sense based on how I had the head oriented on the table when I assembled it.
I did assume that I had the timing correct when I did it with the motor outside of the car. Yet again I have never done timing on a VVT motor and the intake cam definitely is not as user friendly as the other intake cams on earlier heads. Although at most the timing was only off a tooth or so on either side so it should still start, probably would not run great, but start none the less.