When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I have been prepping to do a budget turbo build on my 2000 LS here for the last few months. Now that I have all of my major components, I figured I should go ahead and start a build thread.
My goal with the components I have accumulated thus far is to get the car running on wastegate pressure with stock injectors and stock clutch with minimal fabrication. From there I will work on turning the boost up until I slip the clutch or run out of fuel. I will replace the limiting component\s and then continue until the other component is a limiting factor. Based on my research though, it seems that I will run out of fuel and start slipping the clutch at about the same time.
At this point I, hope to be happy with the cars performance on 91 and will just work getting things fine tuned. If happiness is not achieved, I suppose I will be forced to move on to E85.
Here is a spreadsheet listing all of my components and their cost. I have been doing my best to save money by purchasing as many items as possible on Ebay during their 15% off sales.
I’ll go ahead and list my components here as well:
Garrett GT2560R
T25 Chinese (TacoTaco) cast manifold
BTP (Bell Tuning and Performance) downpipe (It should line up with the manifold…. At least I hope it does)
CXRacing NB intercooler, piping and blow off valve kit (designed for top mount turbo)
Generic T25 waterline kit
EGR Block Off Plate
Turbo compressor inlet and outlet flanges
GM AIT Sensor PN: 25036751 with connector
Exhaust manifold gasket
K&N 2.5” Filter PN: RU-4950
AEM UEGO Wideband PN: 30-4110
Generic T25 ⅝ oil drain fitting
Vibrant PN: 10287 -4AM to 7/16-25 oil restrictor fitting kit
48” -4AN teflon steel braided oil feed line
External wastegate block off
K&N Breather Filter PN: 62-1600RD
⅛ NPT to -4AN adapter
⅜ NPT Aluminum Bung
⅛ BSPT male to ⅛ BSPT female to ⅛ NPT tee
2 wire waterproof connector
Dorman exhaust studs PN: 03415B
Flyin Miata wastegate relocation bracket
Nitrous (Harbor Freight) boost gauge
MegaSquirt 2 Plug and Play for NB1
⅝ barb to ⅜ NPT oil drain bung
⅜ npt drill bit and tap
Duralast J30R7 3ft oil drain hose
In an effort to cut costs, I do acknowledge that I am taking some risks. Just buying things off Ebay and waiting months to use them is definitely one. Another risk is making the assumption that the BTP downpipe is going to line up with the TacoTaco manifold. Based on much of my research, it seems that it should, but who knows if designs have changed. Worse comes to worse, I can just get the BTP manifold. Lastly, like I noted above, the CXRacing cold side piping is designed for a top mount turbo. Im hoping with some light modification that I can persuade it to work with my side mount setup.
While I wait for warmer weather, I am going to start doing as much off the car assembly and prep as possible.
Last edited by atotalpro; 05-07-2019 at 12:36 PM.
Reason: Forgot link to spreadsheet, remove bold
I have run into my first issues with parts. The Mac boost control solenoid I ordered ended up being a fake / counterfeit. When I started questioning the selling about why the paint was flaking off the valve body, they kindly offered me a refund. From my research, it seems like the "P" cast into the valve body is a dead giveaway for a fake.
The second issue I have had is my oil feed tee was not properly deburring from the factory. There is a nice large chunk of stainless hanging inside it. I haven’t decided yet if I want to debure it myself or notify the seller. Since the part was less than $7, and took weeks to arrive, I am leaning towards just deburring it myself.
Looks like you’re off to a good start, but it sounds like you are not planning on installing the megasquirt until later. I’d reccomend at minimum to get that installed and working well before dissassmbly begins just so you have a feel for it. Another suggestion would be a few feet of fire sleeve for the water and oil lines to keep them safe from all the heat. I’ll be following this!
I have been debating whether to do the MegaSquirt install before the pulling the car apart. Either way, it will be a while before I do anything on the car itself and I will definitely consider your suggestion. I will also look into the fire sleeve. Heat management is something I have not fully worked through either. I am currently trying to decided if I should use a turbo blanked and wrap the downpipe as well.
Interesting note about the fake ebc. Is there any downside to running it anyways or do you anticipate it being unreliable and/or failing?
I expect it would have a higher chance of failure. I also don't know what its failure mode would be. If it fails closed, then it could cause an over boost condition. For another ~$50, I can just get a genuine one for FM. I figure it the risk isn't worth the reward.
You should install the megasquirt first like everyone else. It's the right way.
Don't worry about adding the ebc until you have injectors and a reason or capacity to turn up the power. Don't put the cart before the horse.
Originally Posted by Schroedinger
Yes, do the MS before turbo stuff and spend a few weeks learning to tune.
Originally Posted by festersays
Looks like you’re off to a good start, but it sounds like you are not planning on installing the megasquirt until later. I’d reccomend at minimum to get that installed and working well before dissassmbly begins just so you have a feel for it. Another suggestion would be a few feet of fire sleeve for the water and oil lines to keep them safe from all the heat. I’ll be following this!
Welp, looks like there is a consensus. I will plan on installing the MS2 beforehand.
Learning to tune is like running face first into a brick wall. The less questions you have about what is causing the issue (IE: the more stock the car is) the easier it is going to be to climb over.
Not much of an update, but I did get a few more supplies this week.
Timing light
Shell Rotella T6 5w-40
Wix oil filter PN: 51365
Permatex high temp thread sealer
Blackstone oil sample collection kit
From what I have read, Flyin Miata (and most of the internet) recommend switching to 5w-40 for forced induction cars. I am planning to send my oil sample in right before I put the turbo on the car and around the same time do a compression test in order to determine the condition of the engine. That way, if I blow up the engine, I will know if I can blame a pre-existing condition lol.
I am looking into some thermal management products, but my knowledge is very limited on this subject and I was wondering if I could get some feedback / recommendations.
I want to wrap my downpipe and am trying to decide between these three wrap options (cheapest to most expensive):
Cheapo Ebay exhaust wrap
Summit Racing branded exhaust wrap
DEI Exhaust wrap
I also was thinking of running a turbo blanket, although I understand they are controversial.
Thermal Zero brand turbo blanket is the cheapest one I could find that works with a T25 with an internal wastegate. Does this seem like an ok product and is there anything I should be mindful or when purchasing this or any turbo blanket?
Lastly, another member festersays recommended fire sleeve for some of my various lines and hoses. Is there a brand that anyone recommends? Also, is this product appropriate for insulating the following:
As others have said. Do the MS/WB install first. I actually will be following this thread because your intentions are close to mine. I've been playing/tuning with my MSPNP2 now for ~2 weeks...and it's finally looking much better than when first starting. You don't want to be prepped to setup everything mechanical - and realize you still have a few weeks of fiddling with the MS and can't figure out or tune the NA portion of the map since you're spooling up all the time. Get it running pretty nice on the stock motor - and then add all the other mechanical components. I don't even have any boost components (another year away), but I can definitely look back now and say that this would have been a PITA had I not installed it first.
I finally got around to installing my clutch this last weekend, unfortunately made some mistakes during re-assembly and now I am getting some weir trans noises on my test drives such as knocking and excessive bearing noise. On top of that, I installed a used 6 speed I picked up about a year and a half ago from a guy who had, from the looks of it, rolled his NB2. Im not sure how you live through such a thing, but he seemed fine.
He had done a poor job pulling it and I know it had somewhere around 142k on it, but for the price I figured I would give it a go. Now I am pulling the transmission to find out if my noises were a result of a bad transmission or poor installation procedure.
To make the second go around easier, I have purchased an engine support bar from Harbor Freight which I will be using with the scissor type transmission lift I had for the first go around. I figure the extra money is well worth it considering I will be tackling it alone this time.
The 6 speed trans gear oil after 25 miles of driving. I could used this transmission to make metal flake paint. The magnetic drain plug was pretty fuzzy as well as having a chunk of something seemingly non-metallic stuck amongst the metal shavings.
I was able to get the trans pulled again last night. I need to buy a lottery ticket, because my stupidity when installing the trans last time didn't seem to damage the clutch assembly or throwout bearing what so ever.
I don't have a good way to measure input shaft play, but it seems like substantially (1-2mm at the nose) more that my 5 speed as well as the 6 speed sounding a bit more "gravely" that 5 speed when turning the input shaft by hand. After pulling the front bearing cover off the 6 speed, I found some plastic chunks (broken shifter bushing?) in the countershaft bearing and I can see visible play in the input shaft bearing itself. Im considering gambling the cost of an input shaft bearing and more of my time to try and replace it, although the chances that just that bearing is cooked are probably pretty low at this point. Motivation is high to get a working 6 speed, since I have a 3.6 diff showing up on Friday.