Geoff builds a silly 'car' in the few weeks before M@MRLS, every year!
#182
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
Eh, it is a little crooked...
Actually, its a great improvement. I had my 390 breathing through that muffler at one point, isn't it something silly like 3" chambered? Also, how did the drive go on Sunday? There was no way I was going to be conscious early enough to get there by 9am.
Actually, its a great improvement. I had my 390 breathing through that muffler at one point, isn't it something silly like 3" chambered? Also, how did the drive go on Sunday? There was no way I was going to be conscious early enough to get there by 9am.
#183
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2010
Location: Bay Area, CA
Posts: 811
Total Cats: 270
Video will be broken for another hour or so as it's still processing but heres a link.
Last edited by Braineack; 09-03-2015 at 11:24 AM.
#186
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
Ok, so 360 and 4k? What did you steal from work now?
3:10 sounds like it needs a little torsen
Also, how do I made it do directional perspective thing on my phone, like in the Nissan 360 video you sent me the other day
3:10 sounds like it needs a little torsen
Also, how do I made it do directional perspective thing on my phone, like in the Nissan 360 video you sent me the other day
#187
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2010
Location: Bay Area, CA
Posts: 811
Total Cats: 270
It's an awesome drive! Id be happy to do it again!
Depending on how late I stay at work I just may well do that. Need to look up which location this Wednesday is
Camera is one of these guys, pretty cool tech on how it works. V360
It's not technically supported for the really cool 360* video perspective. I'll give it another go tonight and see if I can't convince YouTube to show it that way.
And yeah, I need to put that torsen in pretty badly. I should order axle seals tonight
Depending on how late I stay at work I just may well do that. Need to look up which location this Wednesday is
It's not technically supported for the really cool 360* video perspective. I'll give it another go tonight and see if I can't convince YouTube to show it that way.
And yeah, I need to put that torsen in pretty badly. I should order axle seals tonight
#190
8PM: http://thegarretrestaurant.com
--Ian
#191
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2010
Location: Bay Area, CA
Posts: 811
Total Cats: 270
Can't seem to convince youtube to show the video in the sweet pan around mode :(
Also I've just been informed by my SO that I have a dinner commitment tomorrow evening. It seems unlikely that I'll be free in time to make it to the NCR meet. But now that the car is registered I'm way more likely to show up to them in the future.
TODO list for the exocet (in no particular order):
- Install EO2k's stolen torsen
- Replace the drivers side seat slider connecting rod/cable thing
- Build and install some kind of glovebox/smallish storage under "dash"
- Build and install a rear firewall
- Fix/upgrade the front fuel tank mounts
- Clean up headlight wiring the got borked when I needed to change it up for inspection
- Make and install tophat spacers (probably ~3/4" thick, maybe I'll mill them at work)
- Alignment/corner weighting after raising the car up
- Install MegaSquirt
- Install wideband
- Purchase/install bigger injectors and a fuel pump
- Install trubo? (honestly I'm not 100% sure on this one at this point)
- Make better brake line mounts
- Inspect underside of car after scrapping boat loads on the last drive
- Finish my NB
Also I've just been informed by my SO that I have a dinner commitment tomorrow evening. It seems unlikely that I'll be free in time to make it to the NCR meet. But now that the car is registered I'm way more likely to show up to them in the future.
TODO list for the exocet (in no particular order):
- Install EO2k's stolen torsen
- Replace the drivers side seat slider connecting rod/cable thing
- Build and install some kind of glovebox/smallish storage under "dash"
- Build and install a rear firewall
- Fix/upgrade the front fuel tank mounts
- Clean up headlight wiring the got borked when I needed to change it up for inspection
- Make and install tophat spacers (probably ~3/4" thick, maybe I'll mill them at work)
- Alignment/corner weighting after raising the car up
- Install MegaSquirt
- Install wideband
- Purchase/install bigger injectors and a fuel pump
- Install trubo? (honestly I'm not 100% sure on this one at this point)
- Make better brake line mounts
- Inspect underside of car after scrapping boat loads on the last drive
- Finish my NB
#193
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
4th wednesday of the month is the south bay meet, at The Garrett in Campbell. Yeah, I'll be there (it's like 3 miles from my house). I'll be there in the Audi, because while I've got the new FPR installed in the Miata, I haven't had a chance to go out and retune it for the new pressures yet.
8PM: The Garret of Campbell - Pizza, Burgers, Beer and Friends
--Ian
8PM: The Garret of Campbell - Pizza, Burgers, Beer and Friends
--Ian
#196
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2010
Location: Bay Area, CA
Posts: 811
Total Cats: 270
Haven't done much to the car recently. I ordered suspension spacers from exomotive a while back and am still waiting I'm excited to get them in as it's pretty rough to drive the car as is. A credit card the long ways can rest against the frame and the exhaust sits even lower than that.
This evening I put my MSLABS MS2e in. I had to do some internet sluthing(guessed correctly at file format naming) to find the correct ini file on malabs.gr but I got it connected. Also wtf is with the female db9 connector having mounting nuts, that is not standard!
Set it to narrow band input and scaled the injectors to 260cc and it started right up. I let it idle for about 30 seconds to make sure it would run and then turned in for the night.
I need to figure out a better way to deal with the db9 (I took the side plate off to get the connecter seated well), mount the thing somewhere (zipties!), run a MAP line, and tune. But I'm super happy it just worked when plugged in
This evening I put my MSLABS MS2e in. I had to do some internet sluthing(guessed correctly at file format naming) to find the correct ini file on malabs.gr but I got it connected. Also wtf is with the female db9 connector having mounting nuts, that is not standard!
Set it to narrow band input and scaled the injectors to 260cc and it started right up. I let it idle for about 30 seconds to make sure it would run and then turned in for the night.
I need to figure out a better way to deal with the db9 (I took the side plate off to get the connecter seated well), mount the thing somewhere (zipties!), run a MAP line, and tune. But I'm super happy it just worked when plugged in
#198
Senior Member
Thread Starter
iTrader: (1)
Join Date: Mar 2010
Location: Bay Area, CA
Posts: 811
Total Cats: 270
I think I might make my own side plate and mount the RS232-USB converter inside the case and add a panel mount USB port to the new side plate. I'll probably just be lazy and cut it out of acrylic with the laser cutter at work.