Aidan's loose oily bunghole actually runs a track lap
#402
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Picture dump from pulling the head:
Cylinder 1:
2 and 3:
4:
Bolts:
I found it interesting that some bolts were covered in oil and others weren't.
Grime on one of the bolts:
Ok so the head is at the machine shop. What do I do to the cylinders and block surface while I have it off. What is the best way to clean them.
Anything I need to be careful of when re-assembling?
Also I could tell that my CAS o-ring was about to start leaking out the back, can I get a thicker one or something? I might see if Ed can get me an OEM one.
Cylinder 1:
2 and 3:
4:
Bolts:
I found it interesting that some bolts were covered in oil and others weren't.
Grime on one of the bolts:
Ok so the head is at the machine shop. What do I do to the cylinders and block surface while I have it off. What is the best way to clean them.
Anything I need to be careful of when re-assembling?
Also I could tell that my CAS o-ring was about to start leaking out the back, can I get a thicker one or something? I might see if Ed can get me an OEM one.
#408
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
figure out what that is first. the prep for the head will be differnt for each type, and i assume the block would be too. and reagrding the head, you need to make sure your mahinist knows which type he is prepping for.
#412
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
i like the sandpaper method as it cleans and "resurfaces" the block, but i dont see why either method wouldnt work well.
#413
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
to be honest, ive never used that method. i have done more headgaskets than i can remember and have always used a razor blade to get to clean metal, then "sterilize" the surface with brake clean, leave absolutely no oil/grease/build up or old gasket behind. ive had not one HG fail on me, but they were all composite on (with the exception of a supercharged 3.8 that i can recall)N/A vehicles.
#414
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
do pack the rings with grease, or something equivalent to keep crap from getting in the rings/ring lands. i always used a grease or oil soaked rag. and please note my obligatory ninja edit.
#417
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
weve had customers whos engines ingested sooo much **** it was ludacris, or let coolant sit in the holes for months, so the bores were super rusty. some didnt want to pay for us to pull the bottom end apart to clean everything out and just had us do the headgasket, and not one of those engines had an issue that im aware of. im amazed at what some engines can take. obviuosly this is no excuse to not do it right, but jut some anecdote for ya.
#418
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
get out what you can, wet/dry vac first, followed by compressed air. do an oil change when your done.
weve had customers whos engines ingested sooo much **** it was ludacris, or let coolant sit in the holes for months, so the bores were super rusty. some didnt want to pay for us to pull the bottom end apart to clean everything out and just had us do the headgasket, and not one of those engines had an issue that im aware of. im amazed at what some engines can take. obviuosly this is no excuse to not do it right, but jut some anecdote for ya.
weve had customers whos engines ingested sooo much **** it was ludacris, or let coolant sit in the holes for months, so the bores were super rusty. some didnt want to pay for us to pull the bottom end apart to clean everything out and just had us do the headgasket, and not one of those engines had an issue that im aware of. im amazed at what some engines can take. obviuosly this is no excuse to not do it right, but jut some anecdote for ya.
#419
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
unfortunately, i have no hard science for that and usually didnt touch HLAs on customers cars, just replaced them if they had issues. i have no miata specific experience with HLAs, although i helped one of the shop helpers with his 323 from the early 90, i cant remember if it was a b6 or what though. on one of my nissan KA24s, i painstakingly pulled everyone of those apart and cleaned and reoiled them. it was a fuking bitch, but they were $30 a piece from beckarnly, and more than double that from nissan, and a few were collapsed from 175k of "wife oil change intervals".